Search results
-
Slicks with 10 bolt
350 making 300 or so to the wheels when done hopefully. Probably a 100 shot on top. Factory 273 gears- Hobbz
- Post #5
- Forum: Wheels and Tires
-
What have you done to your square lately??
Ordered seat belts, bed steps, front 1 1/8 sway bar, locker for diff, and brake prop valve. Also replaced all of my brake lines today. -
Slicks with 10 bolt
Right now I have a 10 bolt. It is getting a locker soon, will I be OK to run 29x10.5 slicks or am I going to tear it up?- Hobbz
- Thread
- Replies: 8
- Forum: Wheels and Tires
-
Harbor Freight Coupon Code
http://slickdeals.net/f/1276399-harbor-freight-coupon-thread Hobbz-garage.com -
Hello from WVA
Welcome, I'm just across the hill over in KY. You forgot the pics.......- Hobbz
- Post #6
- Forum: Introduction
-
turn signals dont work but hazards do?
Check and see if you have 12 volts getting to the flasher.- Hobbz
- Post #4
- Forum: Electrical & Audio
-
What have you done to your square lately??
Ill let you know in the spring when the truck hits the road... -
What have you done to your square lately??
Took a few of these off the truck... -
-
OD Green
Rustoleum.... You can use a roller or a harbor freight spray gun.. Lots of YouTube videos on it. Here is mine in flat black rustoleum- Hobbz
- Post #7
- Forum: Paint and Body
-
-
What have you done to your square lately??
Got the wife to help me bleed the brakes today -
-
What have you done to your square lately??
I started wiring my truck from front to back. Got all the heads/tails done and the steering column... -
What have you done to your square lately??
I started mine for the first time today http://www.youtube.com/watch?v=MVYguEBeMuU -
What was your first Vehicle?
Mine was an 81 Oldsmobile Omega that my parents bought when they found out they were having me. It was a tank. Only things there were ever replaced on it were the valve cover gaskets and alternator. It had about 150k on it when I finally sold it and bought a new s10.- Hobbz
- Post #168
- Forum: Other Vehicles
-
What's that sound??? Cracked Flywheel???
I am pretty sure I could tap on the center piece and it would fall out. In your case if you don't have to drive it, no sense in replacing it till to decide what you are going to do.- Hobbz
- Post #18
- Forum: Engine & Performance
-
What's that sound??? Cracked Flywheel???
Finally got the flexplate out. Here is what she looks like- Hobbz
- Post #16
- Forum: Engine & Performance
-
Bed Differences
In my quest for a bed for my truck, I am finding some that have one good side, and one bad. Are the bedsides the same on the 73-80 as the 81-87 except for the fuel door? If so, my search would be a lot easier.- Hobbz
- Thread
- Replies: 2
- Forum: Paint and Body
-
What's that sound??? Cracked Flywheel???
Finally got a video to show everyone. If you look close near the end, you can see the crack http://www.youtube.com/watch?v=skjt8cXvYIE- Hobbz
- Post #14
- Forum: Engine & Performance
-
o2 Sensor Location
thanks guys. heated o2 looks easy enough to do.- Hobbz
- Post #5
- Forum: Engine & Performance
-
o2 Sensor Location
Or maybe it does/did have one and now I need to replace the o2 sensor I snapped off...lol But the question still remains, can I relocate it to on the exhaust after the long tube headers?- Hobbz
- Post #2
- Forum: Engine & Performance
-
o2 Sensor Location
As someone pointed out in another thread, the exhaust that I just took off my 87 TBI 305 to replace, didn't have an o2 sensor. So my question is: Where was the original o2 sensor located, can I move it to after the header in the exhaust pipe, and where did the wire exit the wiring harness so I...- Hobbz
- Thread
- Replies: 5
- Forum: Engine & Performance
-
What's that sound??? Cracked Flywheel???
Thanks. I am going to pull the trans as soon as I done with my rockers and cab corners. Local parts store carries both in Stock along with a new rear main seal so that will get changed too- Hobbz
- Post #12
- Forum: Engine & Performance
-
What's that sound??? Cracked Flywheel???
Flexplate to TQ converter bolts are fine... Thats is the good news. Flexplate to crank bolts are loose or flexplate is broke around those bolts. I can turn the TQ/flexplate back and forth about 1" without the crank moving... Next question, without counting the current one, do I have a 168 or...- Hobbz
- Post #10
- Forum: Engine & Performance
