Converted NP203 grinding sound in 2WD

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
I'm thinking, while you're working at the rear diff, i'll work the rear-output on the tcase. we'll split the work and one of us will find a solution.

If weather permits, i'll pull mine tomorrow :headbang:
 

FitzK25

Junior Member
Joined
Jan 12, 2022
Posts
11
Reaction score
1
Location
Salem, Oregon
First Name
Lewis
Truck Year
1975
Truck Model
GMC K25
Engine Size
350
Sweet well, I’ll definitely get back to it this week and I’ll let you know what I find. Looking forward to your discoveries haha
 

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,121
Reaction score
6,038
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
IT HAS GEAR OIL IN IT?


I found this on a google search since its from someone with more experience than myself, but here you go

2 reasons.
1. The chain requires a thiner oil to lube especialy in cold climates
2. There is a pump in the tail shaft that feeds oil to the rear bearing for both lubrication and cooling. It's basicly a plastic spiral gear like a speedo drive. Gear oil when cold tends to bust that pump and the end result is the rear bearing runs dry and over heats and burns up.


There is a lip in the tail housing that catches oil slung of the chain. The diferential in the tail runs in it and the pump for the tail shaft gets it's oil supply from it. When you convert to part time you MUST put the case in LOC 10 miles every 200 miles to get the chain turning so as to refill this resivior or you will again trash the rear bearing.
Motor oil in the 203. Same flavor you run in your engine is fine weather it be a 10w 30 or a 20w 50. The multigrades will not hurt the case infact they may be better for the same reason as they are in an engine. Multi grades were not common in the 70's when the 203 was produced is why the manuals state 30 weight. Yes in cold climates ATF would be something you could use since it is less effected by low temps but a 5w 30 might be a better choice.



some thoughts: ATF would be whipping up a storm in a system where its not submerged like an transmission usually has its chain(s) in submerged or separately pressure lubed parts.

ATF whipping up air is NOT good for heat and lubricating and your seals would probably not like ATF after so many years, however, this is my theory here. i only mention it because the thing I posted above did and The NP203

I typed most of this then left to do stuff and forgot, so it may seem abrupt but put the right fluid in. if someoen has not said that now
 

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
Thanks Aurora, I'll pay close attention to the pump, it being broke sounds plausible
 

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
I'm going to embed all the images i took today, but look closely at the needle bearings (Pics 5&6) and the thrust washer? (pics 8,9 & 11). The teeth are chewed on pics 2-4 but i dont believe thats the source of the sounds i'm hearing.

with the tail housing out i spun the output and it bound up a few times, only spinning easily in one direction. I beat on it and piece of a washer dropped out (pics 5-6), it spun freely a few times and seized again, beat it again and another of the tiny bearings dropped.

I cant get the nut off the yoke, my largest 1/2 in socket (1 1/8) is too small
edit: did some research, looks like this nut is 1-5/16. O’Reilly has one for $10. i'll pick it up tomorrow

i'm pretty sure the large needle bearings dropped when i separated the tcase, understandably. but where do those tiny bearings go? its not many, so i guess the rest are in the bottom of the case or my catch pan

xc_hide_links_from_guests_guests_error_hide_media
 
Last edited:

RaisedK5

Full Access Member
Joined
Sep 12, 2021
Posts
88
Reaction score
162
Location
Memramcook, New Brunswick, Canada
First Name
Leland
Truck Year
1975
Truck Model
Blazer
Engine Size
350
Those little bearings are part of the trashed thorington bearing dangling from the shaft. Probably a good idea to take the rest of the tail housing apart. Probably sent a couple thru the rear bearings. Looks like an old superwinch part time kit. That's what I had in mine untill I went doubler. Hope you can find a new bearing.
 

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
Looks like an old superwinch part time kit. ... Hope you can find a new bearing.
Mine is a rancho suspension kit, i still have the box. i have no clue what a thorington bearing is, googling now. oh goodness, are these hard to find? I was only under the assumption the chain was hard to get!?!?!?
 

RaisedK5

Full Access Member
Joined
Sep 12, 2021
Posts
88
Reaction score
162
Location
Memramcook, New Brunswick, Canada
First Name
Leland
Truck Year
1975
Truck Model
Blazer
Engine Size
350
That's the one. Shouldn't be impossible. They probably used a common bearing, just have to figure out the number for that one.
 

FitzK25

Junior Member
Joined
Jan 12, 2022
Posts
11
Reaction score
1
Location
Salem, Oregon
First Name
Lewis
Truck Year
1975
Truck Model
GMC K25
Engine Size
350
Ahhh, well that looks like a pretty likely culprit. I believe that torrington bearing is what comes with the MM 501 kit, if you look at the spacer on this page: Should be able to get one that way if you have to. When I get into mine I'll let you know if it's the same problem - I bet it is. With that spacer destroyed, I imagine the 4wd selector ring and the differential drive gear can drift into the differential assembly and make that racket, amongst other things. https://milemarker.com/product/501/#prettyPhoto
 

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
... With that spacer destroyed, I imagine the 4wd selector ring and the differential drive gear can drift into the differential assembly and make that racket, amongst other things. https://milemarker.com/product/501/#prettyPhoto

Oh yes, that makes perfect sense and explains why the teeth are chewed up also, and why the previous owner said it didn't make sounds in 4hi
 
Last edited:

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
Just a couple of updates on my end...

- The 1-5/16 socket i ordered from oreilly auto worked perfectly
- I ordered the 501 kit from MM. I think i have the original internals of the np203 so I plan to convert from rancho to milemarker.

I was concerned about the 2 bearings in the tail housing. i cleaned them up and cannot see any scratching / pitting etc. So i'm going to leave them in place. I dont have a press, so this works out for me.

My parts washer pump has failed, so i'll spend the next couple of days with degreaser and wire wheel cleaning up the casing while i wait on the milemarker parts.

I feel lucky, it not being the chain or something expensive, i hope you have luck as well @FitzK25
 

coolpup32

Member
Joined
Jan 15, 2022
Posts
35
Reaction score
4
Location
MS
First Name
Jeff
Truck Year
1976
Truck Model
k10
Engine Size
350
I'm having trouble cross-referencing this bearing. Can anyone help? Its the rear output bearing, closest to the rear driveshaft. after more cleaning, it feels a bit crunchy

xc_hide_links_from_guests_guests_error_hide_media
 
Last edited:

Latest posts

Forum statistics

Threads
41,850
Posts
903,478
Members
33,363
Latest member
snoblind
Top