Search results

  1. S

    '87 NOS Front Bumper & Fender

    I'm willing to pay good money for a NOS front bumper (w/o black molding) and passenger side front fender. Even a lead would be nice. Thanks guys, Randy
  2. S

    I can't believe I wrecked it......

    For those of you that can't help but look, here you go. I had to tell the original owners son about it yesterday. He tried to hide it, but he looked a little mad at me. Can't blame him.
  3. S

    I can't believe I wrecked it......

    This truck is by far the nicest vehicle I have ever owned. Yesterday I wrecked it, and I'd have to say it's my fault. Luckily my 3 yr. old grandson, the other driver, and myself are fine. It will cost me a front bumper and a fender. Can someone recommend a vendor where I can get NOS parts...
  4. S

    Reading ALDL Connector Codes

    Thanks guys, that's exactly the kind of feedback I was looking for. Again, gotta love this site. Fun to watch and a great resource when you need it.
  5. S

    Reading ALDL Connector Codes

    I found the section of my Emissions & Drivability Manual that speaks to the ALDL connector, how to enter the diagnostic mode, and see codes. It also has a page the describes what each code is for. What I don't see is any guidance on how to interpret the "check engine soon light show" that...
  6. S

    Blow Out Ruined My Truck

    Sorry about the damage. It's ironic that some idots will drive a flat home because they don't want to change a tire. The darn thing will fall apart with pieces flying everywhere like a rubber grenade. And somehow, their cars escape damage. Go figure.:shrug::shrug::shrug:
  7. S

    Need a Good Bed Mat

    Shoulda posted for those looking at bed mats. The fit and quality of this mat could not have been better. Very, very nice.
  8. S

    TBI in Shop Manual??

    "Thanks a lot for the run down chengny, very helpful!
  9. S

    TCC Test Point

    Well, I guess the good news is there is nothing wrong with my TCC and I didn't waste any time crawling all over this truck trying to figure out what was wrong. Of course, the bad news is I don't have a TCC. Thanks a bunch for your help on this.
  10. S

    TCC Test Point

    Oh no!! Section 10 of the 1987 Fuel, Emissions, and Drivability Manual says that the TCC System is used on the 700R4 transmissions. I did not see any mention of the system for TH400's. Did the trucks equipped with TH400's have a lock up converter, or was this system reserved for the 700R4's...
  11. S

    TBI in Shop Manual??

    So I believe the motor in my '87 is idling on the fast side and wanted to look in my shop manual to see what I could learn about settings, adjustments, etc. Heck, I don't even know if there are any you can make. Anyway, I pull out my newly acquired shop manual and I can't find any info on...
  12. S

    TCC Test Point

    yevgenievich, you 'da MAN.:cheers::cheers: Thanks so much guys. First plan is to see if the signal (+12v) shows up when it's supposed to at the test point. If it does, according to the schematics that means my brake switch and the throttle position switch is working properly. After the...
  13. S

    TCC Test Point

    So are you pretty certain the pin out for the Fiero diagram (which is awesome by the way, exactly what I was hoping for) will be the same for my truck? It seems to be pretty specific as it even calls out the engine and trans of the Fiero?
  14. S

    TCC Test Point

    The truck I am currently working on is an '87.
  15. S

    TCC Test Point

    Is there somewhere in the shop manual or wiring schematics that shows the pin out of this connector? I'd really like to see the assignments.
  16. S

    TCC Test Point

    OK, you got me. ALDL connector? I'm looking at my wiring schematics and in the shop manual, but I don't see anything designated as an ALDL connector. The wiring schematic simply shows "Test Connector" 12010997.
  17. S

    TCC Test Point

    I am struggling to find the test point (fuse block?) to help diagnose a problem with my torque converter clutch. Any guidance would be appreciated. Thanks, Stepperado
  18. S

    87 Service Manual Question

    When I had my '84 stepside, I was thrilled to use the wiring diagrams in my shop manual to fix the problem I had with my TCC lock up function. It ended up being a problem with the brake pedal switch. So my '87 K20 happens to have the same issue, the TCC doesn't function. But I pull out my...
  19. S

    Did Chevy Make 3/4 Ton Short Beds?

    Just asking, not sure I've seen one.
  20. S

    Need a Good Bed Mat

    Just an FYI, I found an outfit called Trail FX that sells direct fit bed mats for our trucks. It sounds pretty hefty at 3/8" thick. I should have it by Tuesday.
  21. S

    Need a Good Bed Mat

    I'm sorry, it's a long bed. And you are correct, no spray. Not knocking it, it's just not for me. Thanks, Randy
  22. S

    Need a Good Bed Mat

    Having trouble locating a custom fit bad mat. Nothing generic. Any leads would be helpful. Thanks, Randy
  23. S

    Looking for OEM Style Floor Mats

    I believe that's the one. It's what my '84 still had in it. Got a lead?
  24. S

    Looking for OEM Style Floor Mats

    Can't find OEM style mats anywhere. Certainly someone is making them. Any help would be appreciated. Thanks, Stepperado
  25. S

    Anyone Paint Their Rims Black?

    No skills................ Guess I'll make a request in the other thread category if nobody has anything.

Latest posts

Forum statistics

Threads
42,064
Posts
908,279
Members
33,542
Latest member
willyg
Top