What new tools have you got lately?

Camar068 · Apr 16, 2024

82sbshortbed said:
Nope, I got them at Walmart. I don't remember how much but it was around 15 bucks or so I think. In a white and green box. 40w

You must be registered for see images attach

normal ceiling in the garage I got these and paid ~$20 for longer extensions. They daisy chain so you only plug one in. So for ~$65 you get 6 lights, not including flashing if you don't have reflectors/flashing. Cardboard and metal tape is cheaper than flashing I'm sure....just an option.

Amazon Barrina

Love mine

Blue Ox · Apr 17, 2024

We replaced the flouescents at the shop with 4 and 8 ft LEDs. The 8 ft were from Home Depot, the 4 ft from SuperbrightlLEDs.com

We did some homework before we decided on what to use in our building. If you use a ballast you're not going to see the kind of significant energy savings an LED is capable of. The ballast itself is a big power hog. Plus they're another potential failure point and expense to repair. I think our 4ft fixtures consumption with bypass LEDs was 1/4 of what the florescents used. With a ballast and LEDs my recollection is consumption only dropped by 1/3. The energy savings (at least in this criminal state) more than pays to go to straight LED. In bulk, I believe Superbright's 4 ft tubes were around $6.50 ea.

89Suburban · Apr 17, 2024

82sbshortbed said:
New 12 gallon wet/dry vac

You must be registered for see images attach

I have had this one for quite a while, pretty happy with it. I like the portability of it.

RIDGID 4.5 Gallon 5.0 Peak HP ProPack Wet/Dry Shop Vacuum with Fine Dust Filter, Expandable Locking Hose and Accessories WD4522 - The Home Depot

The rugged RIDGID 4.5 Gallon 5.0 Peak Horsepower ProPack Wet/Dry Vacuum delivers power on the go with a unique, toolbox design engineered for portability and easily accessible storage. Its 5.0 Peak Horsepower

www.homedepot.com

RanchWelder · Apr 20, 2024

You guys are awesome!

REVINKEVIN · Apr 23, 2024

I am building an LT1/L86 6.2 for my 2017 single cab Silverado and I needed to put some new o-rings on my injectors. I had to get this little kit to get them on. I guess that at 2100 psig fuel pressure you just can't roll them on with a little grease.

82sbshortbed · Apr 26, 2024

Got a black and decker da buffer and pads. I'll be using it this weekend on the 84. Let y'all know how it goes.

You must be registered for see images attach

REVINKEVIN · Thursday at 4:28 PM

I got something else. I needed a full length light for under hood work. I found this one that uses the 20 volt batteries that my other Craftsman tools use, and, I saved $20 buying it on eBay. I already have about 12 or so pieces of the Craftsman 20 volt tools so it made perfect sense.

Magna86 · 2024-05-03T18:16:59-0400

I buggered one of the lower control arm threads getting the old bushing out. So I needed to buy a new tap and die set as mine only went up to 1/2' Harbor Freight to save the day and pocket book. The set seems really well made. If I was needing to use these all the time I'd spend for a name brand set but I rarely need one so it will fit the bill.

Titanium Nitride-Coated Alloy Steel SAE Tap & Die Set, 45-Piece

Amazing deals on this 45Pc Titanium Sae Tap And Die Set at Harbor Freight. Quality tools & low prices.

www.harborfreight.com

Catbox · 2024-05-03T18:50:49-0400

Bel Air needed a bath something furious.
Our trusty little pressure washer was not playing nice with us.
So I sent the boy to Harbor Freight after watching a bunch of reviews on YouTube to pick up a new unit.

You must be registered for see images attach

I am happy to report that it works very well and is fairly quiet for a pressure washer.
The Bel Air's before bath photo...

You must be registered for see images attach

and the mostly washed and nearly finished photo.
Much better and going to start working towards putting this one back on the road soon....

You must be registered for see images attach

AuroraGirl · 2024-05-03T19:23:28-0400

Blue Ox said:
We replaced the flouescents at the shop with 4 and 8 ft LEDs. The 8 ft were from Home Depot, the 4 ft from SuperbrightlLEDs.com

We did some homework before we decided on what to use in our building. If you use a ballast you're not going to see the kind of significant energy savings an LED is capable of. The ballast itself is a big power hog. Plus they're another potential failure point and expense to repair. I think our 4ft fixtures consumption with bypass LEDs was 1/4 of what the florescents used. With a ballast and LEDs my recollection is consumption only dropped by 1/3. The energy savings (at least in this criminal state) more than pays to go to straight LED. In bulk, I believe Superbright's 4 ft tubes were around $6.50 ea.

You must be registered for see images attach

I last bought sunco LED tubes to do my shed (Had to do about 40 between my house and shed and garage and a couple for family.)
I have yet to have a single tube fail, 4 of them have been constantly on since 2019 except for power losses once in a while.

Great light output, and single ended power I found to be an advantage because I did most of these overhead on fixtures that were solidly mounted to the ceiling and thus was a little bit of a bear on a step ladder but I did it. Double ended power is safer and requires a bit mrore work. ify ou put a glass tube in a single ended power converted fixture, you will INSTANTLY BLOW UP THE GLASS TUBE which means your face wide open to its doom.

bucket · 2024-05-03T19:38:53-0400

Magna86 said:
I buggered one of the lower control arm threads getting the old bushing out. So I needed to buy a new tap and die set as mine only went up to 1/2' Harbor Freight to save the day and pocket book. The set seems really well made. If I was needing to use these all the time I'd spend for a name brand set but I rarely need one so it will fit the bill.

Titanium Nitride-Coated Alloy Steel SAE Tap & Die Set, 45-Piece

Amazing deals on this 45Pc Titanium Sae Tap And Die Set at Harbor Freight. Quality tools & low prices.

www.harborfreight.com

Did they finally improve them? The sets they used to sell in the plastic cases were utter garbage. Like, completely not usable. Might as well just burn your money. The pipe tap sets in the wood cases are decent however.

Magna86 · 2024-05-03T20:30:05-0400

I have no experience with them before. My other tap and die set is an older craftsman. But the HB set recut/cleaned up the 3/4" threads just fine in the lower control arm shaft.

AuroraGirl · 2024-05-04T09:31:23-0400

bucket said:
Did they finally improve them? The sets they used to sell in the plastic cases were utter garbage. Like, completely not usable. Might as well just burn your money. The pipe tap sets in the wood cases are decent however.

i have a plastic case set from menards.. pure junk. probably can clean threads ok but for cutting them.. no. the taps were better than the dies in this regard, but the hardness on the taps doesnt seem up to snuff. Now the hardness on my plug thread chaser is really nice, but that only has 2 sizes

Edit, apparently using a tap to fix threads is improper so I should be less demanding of my tools when Im using them incorrectly LOL

Ricko1966 · 2024-05-04T10:11:31-0400

Do not buy cheap taps,if money's a problem buy the ones you need in the size you need,as you need them Also buy the correct size drill bit to keep with it. It's not just a convienence factor,it's not galling threads in a block or breaking a bound up tap off. And in general be careful with taps and dies,slow,careful, if it's starts to feel funny back it out,clean out the chips,lubricant and continue, research when you need a bottom tap.I have no idea over time how many guys brought us blocks or heads with Taps or EZ Outs broke off in them. And you cannot drill out broken taps or EZ Outs. They shouldn't even be called EZ Out they should be called Fukt up your whole week thingy.

82sbshortbed · 2024-05-04T10:25:27-0400

Hung my knives up with magnetic tool holders

You must be registered for see images attach

What new tools have you got lately?

Camar068

Supporting Member

Blue Ox

Turning Diesel Fuel Into Fun

89Suburban

Supporting Member

RIDGID 4.5 Gallon 5.0 Peak HP ProPack Wet/Dry Shop Vacuum with Fine Dust Filter, Expandable Locking Hose and Accessories WD4522 - The Home Depot

RanchWelder

Full Access Member

REVINKEVIN

Member

Attachments

82sbshortbed

Fuckemall!!

REVINKEVIN

Member

Attachments

Magna86

Full Access Member

Titanium Nitride-Coated Alloy Steel SAE Tap & Die Set, 45-Piece

Catbox

Full Access Member

AuroraGirl

Full Access Member

bucket

Super Moderator

Titanium Nitride-Coated Alloy Steel SAE Tap & Die Set, 45-Piece

Magna86

Full Access Member

AuroraGirl

Full Access Member

Ricko1966

Full Access Member

82sbshortbed

Fuckemall!!

Similar threads

Latest posts

Forum statistics