What have you done to your square lately??

[CoggedBelt75]

Finally put the cupholder in my square after I took five minutes to make the mod on it today.

You must be registered for see images attach

Looks good. What holds it in place?

 

[80BrownK10]

Looks good. What holds it in place?

The rubber shift boot basically. Normally they just sit on a console by gravity so the shift boot pulled through it gives it even more stability.

 

[TotalyHucked]

Got the front end rebuild buttoned up

You must be registered for see images attach

You must be registered for see images attach

Sent from my iPhone using Tapatalk Pro

 

[AuroraGirl]

Cleaned out my truck bed, re-realized how much bed it isn't, mounted my tool box, and mounted my spare tire which has seen better days on the spare tire rack.

You must be registered for see images attach

 

[bucket]

I really dig that rear bumper.

 

[gotyourgoat]

Cleaned out my truck bed, re-realized how much bed it isn't, mounted my tool box, and mounted my spare tire which has seen better days on the spare tire rack.

You must be registered for see images attach

Are those holes for recessed taillights or exhaust?

 

[AuroraGirl]

I really dig that rear bumper.

It either came off a truck with a rear gas tank or its custom fully. The exhaust parts would be functional if someone chose to run the exhaust there. The license plate holder is fold down. And it has a tongue meant for trailers that dont have balls but holes for pins, its spring loaded and you can adjust the tension to keep the trailer from jerking the truck around. Farmers addition for sure.

 

[AuroraGirl]

Are those holes for recessed taillights or exhaust?

nice timing, just responded

 

[bucket]

It either came off a truck with a rear gas tank or its custom fully. The exhaust parts would be functional if someone chose to run the exhaust there. The license plate holder is fold down. And it has a tongue meant for trailers that dont have balls but holes for pins, its spring loaded and you can adjust the tension to keep the trailer from jerking the truck around. Farmers addition for sure.

I didn't realize that the plate folded down, but I assumed the rest of the stuff. It's really cool!

 

[C10MixMaster]

Turns out the pinging i've been chasing down for the last couple months was not pinging. After playing with timing and jetting it turns out that the vacuum switch for the torque converter would buzz depending on the throttle position it and sounded like pinging. So added a vacuum delay check valve and the noise is gone. Not sure weather to be happy i found it or pissed it took so long. The worst part is i had the valve ready to go in all that time just hadn't got around to it..

You must be registered for see images attach

 

[78C10BigTen]

Cleaned out my truck bed, re-realized how much bed it isn't, mounted my tool box, and mounted my spare tire which has seen better days on the spare tire rack.

You must be registered for see images attach

Wow!!! My bed is terrible but yours makes mine look amazing lol

 

[Poppy 87]

I feel your pain! Having the fix on hand, while going off on another tangent for a repair is a time consuming and costly method. I'm an technician by trade and sometimes it's the basics we over look. Glad that $10 part fix your problem that you spent hours chasing

Sent from my XT1254 using Tapatalk

 

[78C10BigTen]

I feel your pain! Having the fix on hand, while going off on another tangent for a repair is a time consuming and costly method. I'm an technician by trade and sometimes it's the basics we over look. Glad that $10 part fix your problem that you spent hours chasing

Sent from my XT1254 using Tapatalk

I feel that too since it was a simple $65 fix for the noise i was chasing

 

[78C10BigTen]

Soo far that is.... till the PS pump *****

 

[Paladin]

You must be registered for see images attach

Finished scraping and cleaning all gasket surfaces. Now for some new cross hatching with dingleberry hone and it will be ready for the deep fryer treatment in the backyard!