'Snowfighter' dana 60 swap

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Reaperbond

Junior Member
Joined
May 17, 2019
Posts
3
Reaction score
1
Location
Northern california
First Name
Devin
Truck Year
1983
Truck Model
K20
Engine Size
6.2
Hello all. I'm swapping a 1978-1979 "snowfighter" f350 dana 60 into my 1983 k20. Right now i have just 2 questions refarding this swap.
First one concerns the u-bolts: due to the way that chevy and ford mounted the axles being fundamentally different, im wondering how to mount the ubolt (using GM ubolts/mounts) on the driver side directly next to the pumpkin, seeing is there is a piece of webbing (or structure) coming off the pumpkin and terminating at the axle shaft housing, right where the u-bolt is supposed to mount. I am perfectly fine with taking a grinder to it and making a spot for the u-bolt to mount but I just want to see if this is what others have done or found an alternative method.
Second question involves the steering components: my pickup has a 6" lift so I'm wondering if I should get an after-market Pittman arm to replace on the dana 60 or try to find a steering arm to drop the drag link down from the gearbox.
Thanks in advance!
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,905
Reaction score
7,252
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
I dunno, I just have a passenger side D60. Out of curiosity, what are you using for a transfer case and rear axle?
 

CSFJ

-----------------
Supporting Member
Joined
Jul 1, 2014
Posts
6,160
Reaction score
5,162
Location
------
First Name
-------------
Truck Year
-------
Truck Model
-------
Engine Size
-------
It's been a while since I was fluent in Ford axles so I may be off base, but isn't the spring spacing different between the GM and Ford also?
 

MrMarty51

Full Access Member
Joined
Oct 25, 2012
Posts
7,438
Reaction score
9,169
Location
Eastern Montana
First Name
Martin
Truck Year
1978
Truck Model
K20
Engine Size
400
I know not one thing about the axle swap, just saying welcome to the GMSB forum. If it is a snow fighter differential/axle, bring it over, we are suppose to be getting some snow tomorrow so You can try it out. :happy160::happy175::happy175::happy175:
 

Charlie

Mopar by Birth. Chevy by Choice.
Joined
Aug 2, 2017
Posts
1,837
Reaction score
909
Location
Euless, Texas
First Name
Don
Truck Year
1974
Truck Model
Cheyenne 10 LWB
Engine Size
350/TH350/AC/4 BBL Quadrajet
:welcome:
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,024
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
Welcome to the site. I would locate a passenger side drop dana 60. less headaches.
 

Reaperbond

Junior Member
Joined
May 17, 2019
Posts
3
Reaction score
1
Location
Northern california
First Name
Devin
Truck Year
1983
Truck Model
K20
Engine Size
6.2
Thanks everyone for the warm welcome! I got a good laugh about trying it out in the snow haha!
Concerning the axle, the 1978-1979 f350 dana 60 has the same spring spacing (within 1/2") of the chevy spring perches. It took some looking but I finally found the darned thing after looking for 2 years. Unfortunately, the transfer case I'm installing is a driver's drop so I can't use a passenger dana 60.
 

Craig 85

Full Access Member
Joined
Jan 25, 2017
Posts
3,889
Reaction score
4,024
Location
Nashville, TN
First Name
Craig
Truck Year
1985
Truck Model
K30 SRW
Engine Size
454/TH-400/NP205
Are you asking about the webbing under the axle (photo 1)? GM style passenger drop D60's only have 3 U-bolts. The inner passenger side uses studs mounted in the pumpkin (photo 2, dually version axle).

With regards to the Pitman arm, I just used a Skyjacker CA50 arm, but I have a K30 and only went with a 3" lift. I had a K5 back in the early 90's with a 6" lift. I used a raised steering arm and one of those "S" type drag links (PITA). If I had to do it again, I would have used the dropped pitman arm and ORD's steering block #U9018 with a stock style drag link.

You must be registered for see images attach

You must be registered for see images attach


My drop arm (Skyjacker CA50)
You must be registered for see images attach


ORD's D60 Steering arm block
You must be registered for see images
 

Reaperbond

Junior Member
Joined
May 17, 2019
Posts
3
Reaction score
1
Location
Northern california
First Name
Devin
Truck Year
1983
Truck Model
K20
Engine Size
6.2
Are you asking about the webbing under the axle (photo 1)? GM style passenger drop D60's only have 3 U-bolts. The inner passenger side uses studs mounted in the pumpkin (photo 2, dually version axle).

With regards to the Pitman arm, I just used a Skyjacker CA50 arm, but I have a K30 and only went with a 3" lift. I had a K5 back in the early 90's with a 6" lift. I used a raised steering arm and one of those "S" type drag links (PITA). If I had to do it again, I would have used the dropped pitman arm and ORD's steering block #U9018 with a stock style drag link.

You must be registered for see images attach

You must be registered for see images attach


My drop arm (Skyjacker CA50)
You must be registered for see images attach


ORD's D60 Steering arm block
You must be registered for see images

Craig, thank you very much for the info. This is exactly what i was looking for. You were correct about the webbing under the axle in photo 1. Good to know about the 3 ubolts in gm dana 60's, I wasnt aware of that. I will look into the steering arm riser and the lowered pitman arm for the steering.
 

Latest posts

Forum statistics

Threads
41,857
Posts
903,628
Members
33,370
Latest member
mitchell1128
Top