What have you done to your square lately??

[legopnuematic]

greasable hub ujoints? Just went thru this...10 yrs later. Lack of maintenance on my part.

Non greasable/sealed spicer joints for this one.

 

[gilby959798]

Mount repaired, referred to the wrong year mount when I cut these, whatever.

Cab is almost in place, not clearing transfer case, have to cut more.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Grab a high hump replacement panel.

 

[Jrgunn5150]

Grab a high hump replacement panel.

I'll just transfer my original one, need to finish stripping that cab of the stuff I want before I haul it off for scrap. Need to get the bed off the donor before I start loading the trailer back up with scrap.

 

[gilby959798]

I'll just transfer my original one, need to finish stripping that cab of the stuff I want before I haul it off for scrap. Need to get the bed off the donor before I start loading the trailer back up with scrap.

I kept my original one too, that way if I ever build another, I can install it in there and it will be a removable one.

 

[TotalyHucked]

Mount repaired, referred to the wrong year mount when I cut these, whatever.

Cab is almost in place, not clearing transfer case, have to cut more.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You need this to clear the T-case

Transmission Tunnel- 4WD Rear Cover - 73-80 Chevy GMC C/K Truck

Transmission Tunnel- 4WD Rear Cover - 73-80 Chevy GMC C/K Truck AMD Premium reproduction high hump transmission tunnel cover for the 73-80 Chevy / GMC Squarebody Pickup Truck. Typically found on 4WD applications, this cover allows for additional transmission to floor clearance. Be sure to...

www.autometaldirect.com

 

[Jrgunn5150]

You need this to clear the T-case

Transmission Tunnel- 4WD Rear Cover - 73-80 Chevy GMC C/K Truck

Transmission Tunnel- 4WD Rear Cover - 73-80 Chevy GMC C/K Truck AMD Premium reproduction high hump transmission tunnel cover for the 73-80 Chevy / GMC Squarebody Pickup Truck. Typically found on 4WD applications, this cover allows for additional transmission to floor clearance. Be sure to...

www.autometaldirect.com

Yeah, I guess I've never paid enough attention, but it's well beyond the trans hump, and seat area.

 

[TotalyHucked]

Yeah, I guess I've never paid enough attention, but it's well beyond the trans hump, and seat area.

Ahh, gotcha

 

[Mango]

Ah Yes, lots new coat of penetrol to give that rust a patina look, Installed a new EGR pressure sensor to give that New EGR a chance to work properly,
OEM air cleaner and Filter with New Heat Tube from the Manifold, OEM front air intake now looking for the tube to connect the air cleaner to the front intake .....

 

[TotalyHucked]

Set the engine/trans down in the frame on Tuesday to check clearances and start planning for the exhaust

You must be registered for see images attach

Then pulled it back out, threw the engine on the stand and set the cab down on the chassis to get it off the lift. Our owner needed the lift for a couple days

You must be registered for see images attach

 

[aasleson]

Tried some Dodge steelies on the burb but they didn’t fit, so I threw them on the CUCV and they work great.
Also swapped out the alternator and added some extra power and ground cables on the burb.

 

[Travlr]

Tried some Dodge steelies on the burb but they didn’t fit, so I threw them on the CUCV and they work great.
Also swapped out the alternator and added some extra power and ground cables on the burb.

Hard to see them in the shadow...

 

[bucket]

Set the engine/trans down in the frame on Tuesday to check clearances and start planning for the exhaust

You must be registered for see images attach

Then pulled it back out, threw the engine on the stand and set the cab down on the chassis to get it off the lift. Our owner needed the lift for a couple days

You must be registered for see images attach

Can I talk you into chambered exhaust? Pretty please? Lol. The couple times I've heard chambered exhaust on modified LS-based stuff, it was downright cool.

 

[BearKing]

Reassembling the box for my 86 GMC 3+3 Crew Cab 4X4. Then fiberglass repair on the hips. It’s been a long project but it’s getting there.

 

[TotalyHucked]

Can I talk you into chambered exhaust? Pretty please? Lol. The couple times I've heard chambered exhaust on modified LS-based stuff, it was downright cool.

Lol not a chance. I agree, it does sound awesome but it drones like a **** and I as much as I long haul this thing, I couldn't stand it. I know for sure I'm adding resonators to cut down on the clap but haven't decided if I'm gonna keep the Corsa's on it or try something else. I'm gonna plan the exhaust out with "modular sections" essentially so I can change mufflers/resonators easy later on if I wanna try something else.

 

[Ontheboulder]

Getting the rear bumper back together, gonna rebuild the trailer hitch