Which Edlebrock Performer do I have?

[Caddis]

A friend gave me one a few years back.
I went to the website and no luck.
Its for a 350 SB

 

[Manbearpig]

Need more info on it

 

[crazy4offroad]

On the front of the carb down at the bolt flange if you clean it off should have a model number, like 1406. It will more than likely be a 1406 if it is electric choke.

 

[delsolkm14]

On the front of the carb down at the bolt flange if you clean it off should have a model number, like 1406. It will more than likely be a 1406 if it is electric choke.

I think he is talking about a intake, not a carb. I might be wrong though.

If you post pics up, might be able to get a better guess from everyone.

DTB

 

[HotRodPC]

Are you talking about an intake or a carb Norm? As C4 suggested about the #'s on the carb, OR there is only 2 performers in the Intake, An EGR Model, and a NON EGR model. Now there is also the Performer RPM and Peformer Air Gap intakes, but they's say so on the manifolds.
More info, and we can help.

 

[Irishman999]

Does it look like this?

You must be registered for see images attach

 

[delsolkm14]

Does it look like this?

You must be registered for see images attach

Mmmm.... if you want someone to take that off your hands, you could mail it to me, would even pay for the shipping

 

[Irishman999]

Mmmm.... if you want someone to take that off your hands, you could mail it to me, would even pay for the shipping

Its a little dirty now after my oil leak but it might clean up well. Some time in the near future I am switching back to a quadrajet with EGR so I wont have use for it, if you can wait that long.

 

[crazy4offroad]

If he is talking about an intake, the name should be cast into it, behind the carb. "Performer", "Performer Plus", "Performer RPM", "Torker II" etc. Then you just look the name up for the platform (350) and you'll have your model number, depending on finish, like if it's plain, polished, powder coated, etc.

 

[Caddis]

Its an intake. performer. Thats all it says. It has some patent numbers on the bottom underneath but thats it.

 

[crazy4offroad]

Non-EGR should be model #2104, if it has EGR it will be a #3706.

 

[Caddis]

I think I just figured out that its a Performer Air-Gap (Idle - 5500 RPM).
Thanks everyone.
I also noticed it has a crack near the water jacket. I hope I can just weld that.

 

[HotRodPC]

I think I just figured out that its a Performer Air-Gap (Idle - 5500 RPM).
Thanks everyone.
I also noticed it has a crack near the water jacket. I hope I can just weld that.

That is just a performer w EGR. Not an air gap. Air Gap, has an Air Gap at the front of the intake to draw air in like a scoop to cool the plenum.
Yes, you can have that heliarced. I'd pull the temp sensor out and let the cracks close up first, then grind a small trough in the crack and fill it. Be careful not to go to deep and damage those threads, or you'll have a thread leak forever.

 

[Caddis]

That is just a performer w EGR. Not an air gap. Air Gap, has an Air Gap at the front of the intake to draw air in like a scoop to cool the plenum.
Yes, you can have that heliarced. I'd pull the temp sensor out and let the cracks close up first, then grind a small trough in the crack and fill it. Be careful not to go to deep and damage those threads, or you'll have a thread leak forever.

But HotRod , I was just at the website loking a bit closer and the reg Performer has a much different bolt pattern and intake for the carb.

 

[HotRodPC]

You have the 3701. It's not Air Gap. Here it is on Summit.

http://www.summitracing.com/parts/EDL-3701/?rtype=10