Search results

  1. Taylorb27

    Issues finding a th350 o ring kit?

    So admittedly I’m not the most knowledgeable when it comes to th350 rebuilds so my brother in law is doing my th350. He’s no pro but hes built more than I have. I already had clutches, steels, a shift kit and a thrown together seal kit from stuff I had laying around. Basically the only seals...
  2. Taylorb27

    84 c10 dual headlights retrofit?

    My 84 Scottsdale with the single headlights and marker lights below. My plan is to replace the headlight with a pair of black led h6054 with amber turn signals built into them and try to find either a light bar or other aftermarket light housing to fit in the market housing spot. It will...
  3. Taylorb27

    Th350c rebuild or just re seal?

    So the front seal on my 84 c10’s th350 completely let go and is leaking trans fluid like mad. It started a block away from home when I gunned it and it’s been parked ever since. Now that I’ve got all my ls swap parts together I’ve decided it’s time to tackle the trans, question is should I...
  4. Taylorb27

    Th350c major leak & future behind an ls?

    So the th350c in my 84 c10 decided to leave a nice oil slick about 4 blocks to my house. Looks to be leaking from inside the bell housing as it’s leaking from my starter and somewhere on the driver side. Guessing the oring seal for the TC or a front seal? Anyway this is jumpstarting my LS swap...
  5. Taylorb27

    Anyone have any Jeep wj quadratrac experience?

    Seems the Jeep forum I’m on is dead on the wj side. Recently I picked up a 1999 Jeep Grand Cherokee 4.7l with the full time quadratrac posi 4wd system. The best part is it was FREE! Body is great, no rust at all.. it was driving awesome, started right up, has an exhaust manifold leak but I’ll...
  6. Taylorb27

    New blower motor shot??

    So I’ve had a terrible, very loud squealing noise coming from what seems to be the blow motor. It’s not a constant squeal but when it chirps it hits loud and hard, can here it a few blocks away lol well I figured i just needed a new blower and that was that. Put the new blower in tonight and...
  7. Taylorb27

    Wheel lip rubbing on UCA’s

    I posted this to the wheel and tire section but it’s probably better suited for this section. looking at ways around this, I know I could run a spacer but the front fitment is just how I want it. Will be lowering soon. First question, would cut coils drop the UCA inside the wheel? Will be...
  8. Taylorb27

    17x9 +20mm offset wheels rubbing UCA

    Yes I know I know I should have googled first... looking at ways around this, I know I could run a spacer but the front fitment is just how I want it. Will be lowering soon. First question, would cut coils drop the UCA inside the wheel? Will be cutting at least a coil, possibly 2 and doing an...
  9. Taylorb27

    Headlights and turn signal issue

    I've been googling and searching around but I can't quite find my answer. I'm sure it's a ground issue of some sort I just want to get an opinion, after a bit of thinking I guess it could possibly be a indicator switch? Anyway here it goes.. Headlights off -- left and right indicators work in...
  10. Taylorb27

    Edelbrock 1406 choke wire?

    I just swapped an Edelbrock 1406 onto my engine and everything works good performance wise (with the choke locked open) but for some reason I can't get my choke to heat up. I just assumed that the factory choke wire for the qjet (electric choke) would work but maybe I am wrong. I do have full...
  11. Taylorb27

    Too much sh** to clean by hand?

    Bought a 5.3l off a running pickup. A pickup that I knew and have driven around in. Apparently the owner wasn't too religious with oil changes though as it is GUNKED up. Judging from my pictures that I'll post have you had luck cleaning a super gunked up engine with carb clean and a brush? I...
  12. Taylorb27

    are quadrajet baseplates the same flavor?

    basically wondering if rochester calibrated their baseplates like they do bodies on the qjets. i went to swap idle mixture screws from a qjet from 72 model carb to my 84 model carb and the thread size and pitch is very different. wanted to swap due to the fact that my 84 model has the odd head...
  13. Taylorb27

    Thick black/red tint sticky stuff on fuel line

    As the title says I've got this blackish with a red tint substance on the inlet and outlet of my fuel filter. It's super sticky and doesn't smell like anything. It's thicker and stickier than anything I've seen in a tank. I don't have any sediment in my fuel filter but the fuel is somewhat...
  14. Taylorb27

    comp 12-671-4 nostalgia?

    Anyone running this cam in their trucks? Have a chance to pick up a whole kit (cam, lifters, springs, timing chain set) for little to nothing. Would be going in a 350 with stock 487x heads. Flat top pistons. I maybe work the heads a bit but nothing major. Duration @ .050 is 229 on the intake...
  15. Taylorb27

    El Camino headers on a C10?

    I know it's easier to fit car headers on trucks but just seeing if anyone has taken long tubes meant for an el Camino (mid 70's) and put them on their square? Can get a brand new set from a buddy for a case of beer. Might just get them and see anyway. My welder and I do get along so it shouldn't...
  16. Taylorb27

    84 C10 charcoal canister line question

    Replaced the current qjet with a good older rebuilt one I had due to not having to hack up the baseplate to get to the idle mixture screws. Older one does not have a front port coming off the fuel bowl. I'm guessing the older pickups had that line running to the air cleaner? If they even had...

Latest posts

Forum statistics

Threads
42,201
Posts
911,214
Members
33,696
Latest member
brianbones
Top