Goodwrench crate engine smoking from passenger side exhaust

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
So I just picked up this Frankenstein truck that’s got a goodwrench 350 with “<30k” on it. It’s been sitting some odd years due to previous gent said it was flooding out and running rich. I put a battery on it gave it a shot of brake clean and it fired right up and idled, but it’s most definitely got an issue flooding the passenger side, I removed a plug and there was fuel dripping off of it. I also broke that spark plug so I’m changing them. Can I run what I use in all my other 350’s? Ac Delco r44t or r45ts? I’ve got both available. But anyways what I was getting at is there’s a fog coming out of passenger side tailpipe(dual exhaust) it’s a lighter color (hoping not white) and it gets darker with more throttle until it’s black. (Drivers side blows a little dark smoke with a serious rev). I’m not sure where the distrivutor is at but I can’t retard it enough to get the timing line onto the timing tab, #1 on the cap is around 6’ o’clock. I’m thinking start with completely redoing the timing as a start and then work on the quadrajet. I guess I could just rotate the plug wires one round. During retarding the timing the truck would barely run and had little to no throttle input before a puff out of the carb followed by smoke. Ps the sound of secondaries opening on a quadrajet never gets old lol
 

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
1,589
Reaction score
2,150
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
Sounds like it was over advanced in an attempt to compensate for a rich condition. Black smoke fuel. Assume choke is open. Yes, being as it is an unknown quantity go back to basics, check everything tune up related. If possible, when running look down ventures for fuel dripping, if it is, that's a problem.
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
By over advanced do you mean a tooth or few off when the distributor was put in? I slightly advanced the timing to where the coil cover was straight side to side because that’s usually where I start and the truck wouldn’t start, slightly retard it and it fired right up but the timing mark is still showing wayyyyy advanced(around the top of the harmonic balancer, timing tab being by the ps pump)
 

85 Squarebody76

Full Access Member
Joined
Dec 12, 2021
Posts
63
Reaction score
80
Location
Missouri
First Name
Bob
Truck Year
1985
Truck Model
GMC C1500
Engine Size
305
So I just picked up this Frankenstein truck that’s got a goodwrench 350 with “<30k” on it. It’s been sitting some odd years due to previous gent said it was flooding out and running rich. I put a battery on it gave it a shot of brake clean and it fired right up and idled, but it’s most definitely got an issue flooding the passenger side, I removed a plug and there was fuel dripping off of it. I also broke that spark plug so I’m changing them. Can I run what I use in all my other 350’s? Ac Delco r44t or r45ts? I’ve got both available. But anyways what I was getting at is there’s a fog coming out of passenger side tailpipe(dual exhaust) it’s a lighter color (hoping not white) and it gets darker with more throttle until it’s black. (Drivers side blows a little dark smoke with a serious rev). I’m not sure where the distrivutor is at but I can’t retard it enough to get the timing line onto the timing tab, #1 on the cap is around 6’ o’clock. I’m thinking start with completely redoing the timing as a start and then work on the quadrajet. I guess I could just rotate the plug wires one round. During retarding the timing the truck would barely run and had little to no throttle input before a puff out of the carb followed by smoke. Ps the sound of secondaries opening on a quadrajet never gets old lol
Is there not a brown wire next to the power brake booster ?? If so you need to disconnect it to set the base timing.. Not sure what year truck your working on '86 or'87 and up has the wire..
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
It’s not a throttle body truck. It’s a Frankenstein truck. 1981 c10 cab on a k20 frame. Finding new things everyday with it. My 87 has the brown wire you’re referencing however.
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,017
Reaction score
1,808
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
I had one wet plug and a tick from that side of the engine. Turned out the rocker arm polylock had loosened enough to let the pushrod pop out of the recess. Basically one dead cylinder.
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
This engine does have almost what I’d call a diesel injector noise? At the passenger side. I’ll try to pop off a valve cover and check it out. I plan on doing a tuneup since one spark plug wire is different so new plugs, wires, redo timing, fix the quadrajet since I actually want to keep it etc
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
I did notice while fiddling with the carb that when the secondaries open you can see fuel dribbles come out and land on the top air door. Is that normal? Or is that just more verification it’s dumping fuel from somewhere
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,017
Reaction score
1,808
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
What type of carburetor do you have? On a Quadrajet or Edelbrock the secondaries open based on air flow, so nothing happens to move the secondary flaps when you actuate the throttle with the engine off.
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
It’s a quadrajet, I noticed that with engine running when I was playing with the carb and timing.
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
Popped valve cover off….
You must be registered for see images attach
You must be registered for see images attach

Can’t feel the lifter down in the hole either, so uh what causes a new crate engine to do this? All the valve cover bolts were hand tight that’s why it’s so greasy come to find out. It’s fairly clean under the sludge. Inside the valve covers wasn’t terrible but not what I’d expect from a “new” engine. Supposed to be around 5 years old I’m told with under 30k
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
It ran surprisingly well for a completely dead cylinder. What should I do to go about getting this engine back going? I planned on using the engine in something else when I was done with the truck. Can I just pull the intake check out the lifters replace what needs replaced and reassemble?
 

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
5,882
Reaction score
9,622
Location
Washington
First Name
Todd
Truck Year
1986
Truck Model
K20
Engine Size
454
First thing I’d do is pop a new pushrod in it, set ALL the valves since one was obviously loose? and see how it runs.
And yes that could be a 30k mile engine. With no oil changes!
 

iamtherealJayy

Full Access Member
Joined
Nov 26, 2021
Posts
1,571
Reaction score
275
Location
Tennessee
First Name
Jacob
Truck Year
1987, 1978, 1976
Truck Model
V20, K10, K10
Engine Size
350, 350, 350
I tried to just sit another pushrod in and it just sunk down the whole way, the lifter is gone to visit somewhere so I’m assuming pull the intake and put the litter back in and go from there. Surprisingly I theres a memo book of maintenance and new parts in the glove box and the only thing in there is radiator repair and coolant stuffs… uh oh hope it hasn’t been over heated
 

Latest posts

Forum statistics

Threads
41,849
Posts
903,449
Members
33,362
Latest member
Dhatch84
Top