Door Hinge Spring Replacement

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Rickf

Full Access Member
Joined
Jul 29, 2017
Posts
559
Reaction score
695
Location
Grafton NH
First Name
Rick
Truck Year
1974, 1954 & a 1937
Truck Model
K20
Engine Size
350
That's on my '93.
 

Snoots

Full Access Member
Joined
Jan 23, 2013
Posts
8,569
Reaction score
17,354
Location
Georgia
First Name
Roger
Truck Year
1973
Truck Model
Jimmy Sierra
Engine Size
350 w/203
BTW: while researching this I came across a YouTube video about how to easily fix door pops on a C10. My passenger door did that, and I’ll be damned if it doesn’t work. I’m sure most of you were already aware of this but I sure wasn’t, and always pleasure to come across a free and instant fix:

xc_hide_links_from_guests_guests_error_hide_media
Yeah, but those rollers are supposed to turn freely and NOT be stiff as his. He needs to clean out the old grease. He's welcome.
But that video does nothing to help with the spring.
I found replacement springs at CJ Pony Parts but nothing on how to replace them.
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
3,079
Reaction score
7,115
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
Here is the tool, Cut up a socket to make one if you can't find it to buy. The tool works great. 1/2" drive

You must be registered for see images attach


You must be registered for see images attach
 

C10_Blackie

Full Access Member
Joined
Jan 2, 2024
Posts
64
Reaction score
138
Location
Seattle, WA
First Name
Rob
Truck Year
1981
Truck Model
C10
Engine Size
350
Yeah, but those rollers are supposed to turn freely and NOT be stiff as his. He needs to clean out the old grease. He's welcome.
But that video does nothing to help with the spring.
I found replacement springs at CJ Pony Parts but nothing on how to replace them.
Yeah - I see now that my rollers are binding because of paint overspray. But it was a nice quick fix for me to give the roller a turn and have the door start closing nicely again.

I ordered a replacement left-hand spring from LMC and I guess I'm going to find out for myself if it's possible to get one of these things on without removing either the door or the fender. From what people said earlier in this thread, I guess it can be done.
 

C10_Blackie

Full Access Member
Joined
Jan 2, 2024
Posts
64
Reaction score
138
Location
Seattle, WA
First Name
Rob
Truck Year
1981
Truck Model
C10
Engine Size
350
Got it, I think. I was having problems visualizing what needs to be done. Turns out at least C3 Corvettes have a similar spring and now I can see how the tool suggested above would work. I think I might be able to do it with a thin pry bar. Here's the basic procedure:

xc_hide_links_from_guests_guests_error_hide_media
 

Old Guy Bill

Full Access Member
Joined
Sep 10, 2023
Posts
417
Reaction score
1,274
Location
KY
First Name
Bill
Truck Year
1978
Truck Model
K20
Engine Size
400
On my ‘78 hinges the springs seemed OK, but both rollers were beyond repair.
I just replaced the whole hinge on both sides.
 

C10_Blackie

Full Access Member
Joined
Jan 2, 2024
Posts
64
Reaction score
138
Location
Seattle, WA
First Name
Rob
Truck Year
1981
Truck Model
C10
Engine Size
350
I’m pleased to report that the method in the video for the Corvette also worked on my 1981 C10. You don’t have to remove the door or the fender. You just have to drop the spring into position, pry it over from the bottom and tap it up into place.

There isn’t a lot of room to work in there so you will definitely need a thin pry bar/tool like the one used in the video. There was nothing in my garage that would work. I was about to head to the hardware store and happened to run into a neighbor who had a little bar that had just enough of a bend to get it done.

Nice to not constantly get hit by the driver’s door anymore.
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
3,079
Reaction score
7,115
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
....... I can see how the tool suggested above would work. I think I might be able to do it with a thin pry bar.
Glade you got it! The tool actually works from the top. Hook the spring on the bottom, and slide it up. With the tool in place, short extension and ratchet at the top, twist to hold a little tension. Remove your hand, twist the tool and spring around where it goes, push down on the ratchet to set the spring. With the tool, less than 10 seconds.

I did some springs the way you did until I got the tool.
 

C10_Blackie

Full Access Member
Joined
Jan 2, 2024
Posts
64
Reaction score
138
Location
Seattle, WA
First Name
Rob
Truck Year
1981
Truck Model
C10
Engine Size
350
Glade you got it! The tool actually works from the top. Hook the spring on the bottom, and slide it up. With the tool in place, short extension and ratchet at the top, twist to hold a little tension. Remove your hand, twist the tool and spring around where it goes, push down on the ratchet to set the spring. With the tool, less than 10 seconds.

I did some springs the way you did until I got the tool.
Thanks! Once you get the hang of it, prying it over from the bottom isn’t hard - but I’d be happy to never have to do it again…
 

Latest posts

Forum statistics

Threads
43,743
Posts
941,948
Members
35,696
Latest member
iickyslicky
Top