81 Silverado- Keeps blowing speedometer Transducers

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Mark97213

Junior Member
Joined
Apr 26, 2019
Posts
19
Reaction score
1
Location
Portland, OR
First Name
Mark
Truck Year
1981
Truck Model
1500
Engine Size
5.7
Greetings all. Looking for some advice on why I might keep blowing speedometer transducers. I've gone through two replacements and although they work fine for about 30 minutes, they eventually just stop and the speedometer fails. Any idea what would cause the transducers' to keep failing? Rebuilt transmission with new speedometer plastic gear in transmission. I'm at a loss.

You must be registered for see images attach
 

C10MixMaster

Full Access Member
Joined
Dec 6, 2016
Posts
756
Reaction score
1,424
Location
Kingman AZ
First Name
Ben
Truck Year
1977
Truck Model
C10 BIG10
Engine Size
ZZ4 350
well there are only two parts that could cause a cruise transducer to fail like that the speedometer or upper cable. Are you sure the transducers are actually failing? If so i would lean towards an upper cable needing oil or replacement. or did the upper cable come loose from the speedometer? Since you played with the gears in the tranny i would not write of the possibility cable or gear problem there to.
 

Preston

Full Access Member
Joined
Jan 25, 2019
Posts
787
Reaction score
354
Location
Mechanicsville VA
First Name
Preston
Truck Year
1983
Truck Model
k10
Engine Size
350
Welcome from Virginia:boti: to GMSB
I’m sure you (we) will be able to find a solution to your problem
 

Charlie

Mopar by Birth. Chevy by Choice.
Joined
Aug 2, 2017
Posts
1,837
Reaction score
911
Location
Euless, Texas
First Name
Don
Truck Year
1974
Truck Model
Cheyenne 10 LWB
Engine Size
350/TH350/AC/4 BBL Quadrajet
:welcome:
 

Mark97213

Junior Member
Joined
Apr 26, 2019
Posts
19
Reaction score
1
Location
Portland, OR
First Name
Mark
Truck Year
1981
Truck Model
1500
Engine Size
5.7
well there are only two parts that could cause a cruise transducer to fail like that the speedometer or upper cable. Are you sure the transducers are actually failing? If so i would lean towards an upper cable needing oil or replacement. or did the upper cable come loose from the speedometer? Since you played with the gears in the tranny i would not write of the possibility cable or gear problem there to.

The cables seem to turn fine but I can't imagine any binding issues since they work fine for 30 minutes or so. Could there be a bind in them that's subtle, causing them to slowly burn up the transducer? Doesn't seem likely.
 

C10MixMaster

Full Access Member
Joined
Dec 6, 2016
Posts
756
Reaction score
1,424
Location
Kingman AZ
First Name
Ben
Truck Year
1977
Truck Model
C10 BIG10
Engine Size
ZZ4 350
The cables seem to turn fine but I can't imagine any binding issues since they work fine for 30 minutes or so. Could there be a bind in them that's subtle, causing them to slowly burn up the transducer? Doesn't seem likely.


if the transducer if failing the only thing i can see is something binding. since you have eliminated the "likely" now we have to consider the unlikely. remember that cable is spinning 1000 rpm at 60 mph. so a little friction could be a lot at speed. Have you ever seen a speedometer read steady at low speed and jump around at high speed that usually a binding cable. the other possibility is bad parts back to back. i have put in three alternators back to back two were bad rite out of the box! oil is a lot cheaper than a transducer thats were i would start. hope this helps
 

Mark97213

Junior Member
Joined
Apr 26, 2019
Posts
19
Reaction score
1
Location
Portland, OR
First Name
Mark
Truck Year
1981
Truck Model
1500
Engine Size
5.7
if the transducer if failing the only thing i can see is something binding. since you have eliminated the "likely" now we have to consider the unlikely. remember that cable is spinning 1000 rpm at 60 mph. so a little friction could be a lot at speed. Have you ever seen a speedometer read steady at low speed and jump around at high speed that usually a binding cable. the other possibility is bad parts back to back. i have put in three alternators back to back two were bad rite out of the box! oil is a lot cheaper than a transducer thats were i would start. hope this helps

Thanks for that, I think you may be right. The speedometer worked fine for around 30-45 minutes but then it starts getting erratic and then it fails. When it does, you can hear noise from the transducer which led me to believe I just simply bought a poor remanufactured transducer. So I bought a second one, from a different supplier and the same, 30 minute use, it failed as well. Seems unlikely to get two bad transducers from different suppliers. I'm thinking maybe I should just replace the upper and lower speedo cables. Probably unlikely but could any of the electrical connections be causing them to burn up? I suppose there could be some binding in the speedo itself, no?
 

C10MixMaster

Full Access Member
Joined
Dec 6, 2016
Posts
756
Reaction score
1,424
Location
Kingman AZ
First Name
Ben
Truck Year
1977
Truck Model
C10 BIG10
Engine Size
ZZ4 350
Thanks for that, I think you may be right. The speedometer worked fine for around 30-45 minutes but then it starts getting erratic and then it fails. When it does, you can hear noise from the transducer which led me to believe I just simply bought a poor remanufactured transducer. So I bought a second one, from a different supplier and the same, 30 minute use, it failed as well. Seems unlikely to get two bad transducers from different suppliers. I'm thinking maybe I should just replace the upper and lower speedo cables. Probably unlikely but could any of the electrical connections be causing them to burn up? I suppose there could be some binding in the speedo itself, no?


the speedo binding is less likely but not impossible. The ones i have seen fail made a screeching scraping noise. i would put a drop or two of light weight oil or atf on the rear bushing just in case.
 

Mark97213

Junior Member
Joined
Apr 26, 2019
Posts
19
Reaction score
1
Location
Portland, OR
First Name
Mark
Truck Year
1981
Truck Model
1500
Engine Size
5.7
I'm afraid to buy a third transducer at $100 and have the same result. I guess if one cable turns freely but not the other as freely, seems like that could cause the transducer to burn up. Just a guess. I think I may just buy new upper and lower speedo cables to rule them out. Just seems odd.
 

Forum statistics

Threads
43,936
Posts
946,049
Members
35,982
Latest member
jake26104
Top