Search results

  1. P

    Z-bar linkage for mechanical clutch pedal.

    $40 OBO. Out of an 84 K10. Frame bracket and z-bar with linkage to pedal. There is some wear damage to the linkage as shown. Could be repaired.
  2. P

    Dust cover for sm465 bellhousing.

    Came off of a '84 K10. Used but in pretty good shape. $20 located in florence SC. Willing to ship.
  3. P

    Torque converter lockup relay w/ pigtail

    Part#14014515 with the plug and wire harness. $20 in florence, SC. Willing to ship.
  4. P

    Cruise control harness 86 K5

    This is all of the cruise control parts taken from a 86 Blazer. The wiring harness is cut after the plug coming out of the controller, but there's enough length there that they could easily be put back together. $40. In Florence, SC.
  5. P

    Wts: Wiring harness out of an 84 k10

    I have this harness that I pulled before I scrapped my old pickup. I'm not going to use it, so if anyone wants it, here it is. I'm not sure if any changes were made over the years. I dont notice but 1 cut wire, so I assume it's all here. Dont really know what it's worth. Maybe $35. I'm in...
  6. P

    Stainless brake line for 10 bolt rear axle

    Used stainless line with stock length rubber line for a 8.5" 10 bolt. Bought the full truck kit from LMC and these are part of that kit. I will split them to ship, but they were installed and run but are unhurt. $50 in Florence, SC or ship on your dime.
  7. P

    10 bolt carrier

    2.73 and up carrier out of a 28 spline 10 bolt 8.5" axle. $40 in florence, SC or ship on your dime.
  8. P

    1350 yoke for 10 bolt

    Yoke out of a 10 bolt. Fits a 1350 u-joint. Comes with straps and bolts. $45 in florence, SC or ships on your dime.
  9. P

    Mounting a heavy belt-driven air compressor

    I've got an old Bendix TU-FLO 400 sitting in my garage that I'm looking at using for on board air. They used to be used for air brakes and such on big trucks so I know it'll work fine, but the issue is it's like 35 lbs. Anybody come up with any mounting options for such a thing? A york would be...
  10. P

    dimensions for slave cylinder bracket

    I'm trying to convert my mechanical clutch SM465 to hydraulic using stock GM parts instead of the overly expensive aftermarket slave cylinders or forking out the cash for a new bellhousing. Does anyone have a hydraulic bellhousing that they can pull some dimensions off of for the location of...
  11. P

    Floor anchors for rear seat K5/Suburban

    I'm looking for a pair of the brackets that the rear seats hook into in the floor. I'm doing something custom and it would save me some fab time. Anybody have a set they cut out of one?
  12. P

    Bumper with bumperettes from a '86 K5

    Florence,SC I will not ship. It looks really straight, not mint condition but should clean up good. I took it off and dont need it. Previous owner crappily painted it black. Doesn't look like they bothered to do any prep work to the chrome. $20 or a case of beer. I just want it gone.
  13. P

    Remote mounting battery. Wiring questions.

    I'm relocating my battery to roughly the rear seat of my '86 K5 as part of the rewire during my LS swap. My plan is to keep all of my connections in the engine bay, so I'm going to mount a main power bus bar and a secondary fuse block for accessories and such. I think I need to run a power and...
  14. P

    Parking brake pedals

    I have 2 parking brake pedal assemblies. Top one was out of a 84 K10, bottom was in a 86 K5. They both work. I also have 1 pull lever that I'll throw in if someone wants it. $25 each or $45 for both +the ride. https://i.imgur.com/W0RnqjG.jpg
  15. P

    Dash controls for delay wipers?

    During my LS swap I'm wanting to go to an aftermarket steering column and move my wiper controls to the dash. I'm looking for a decent switch that I can make work and I'm not coming up with much. It's a delay-hi-low motor. Does anybody know of anything good that I could wire in? The best...
  16. P

    Use donor cluster in LS swap?

    My L59 came with the stock cluster out of the Tahoe it lived in. Is it feasible to use the cluster out of the newer truck or is there more involved than just wiring it to the computer? I'm building a custom dash, so making it fit isn't a concern.
  17. P

    L59 swapping into 86 K5. Crossmember?

    I'm picking up a L59 out of a 2002 Tahoe and I haven't found a conclusive answer on whether I'll have oil pan/ crossmember interference. Anybody have any knowledge?
  18. P

    How much slip does the stock front driveshaft have?

    I moved the axle in my Blazer forward an inch and have just now gotten around to regearing it after my 14 bolt swap. The problem is my slip in the driveshaft seems to stop right about the time it gets to the yoke at ride height. Looking at the witness marks, it looks like it only goes about 2"...
  19. P

    Cheap options to replace Blazer seat belt?

    I'm doing big things to my K5, and one of the things I really want to get rid of is the stock seatbelt with the button that sticks through the door. Running it without the door makes the belt not lock if I get in a wreck, and I don't trust the plastic button not to break down the road, so my...
  20. P

    New rear bumpstop questions.

    I have a 3" block in the rear, so obviously my bump stop doesn't reach any more. I have 2 questions because of that. 1. Do I need to move my bump stop the same amount as my lift? I don't know if the factory ones were based on not over-flexing the leaf springs or something else. 2. How are you...
  21. P

    Wheel cylinder link part number

    This is the saddest thing I've ever had to come to the forums to ask. I'm rebuilding a 14 bolt ff axle to go in my K5 and I need new wheel cylinder links (the pins in each side of the drum brake cylinder) but I can not for the life of me find a part number to the correct ones. Can anybody help...
  22. P

    Stock Humvee rims on a front 10 bolt?

    Trying to work out my 8 lug rear/6 lug front issue. If I put 2" thick 6 lug -> 8 lug adapters on my front 10 bolt can I run stock Humvee take offs? I'm pretty sure I can run them as-is on my rear 14 bolt, but the front is the big question. I'm not afraid of trimming sheet metal as needed, but...
  23. P

    14 bolt ff out of a 3/4 ton into a 1/2 ton.

    I picked up a full float over the weekend that came out a C20 in the late 70's. I know the spring perches are the right width but I saw something about the shock mounts being different because it's a 2wd. Does anyone have experience with these that can tell me how direct the swap is? I know...
  24. P

    Half doors that keep the vent window?

    Has anyone ever seen a door cut down while retaining the vent window? I'm planning on chopping up a set that I have but I'm looking for a little uniqueness. It'd be nice to still be able to force the wind in the cab since I don't have a/c. Not sure if it's worth it yet, but I would love to...
  25. P

    Time to clean out my garage. Bunch of leftover parts.

    Round 1 of trying to make room in my garage. Everything is make an offer/OBO. Located in Florence, SC. The more you buy the easier it will be to talk me down on prices, I really want to get rid of the clutter. 700r4 ->NP208 low adapter $35 factory oil cooler adapter, lines, and radiator...

Latest posts

Forum statistics

Threads
42,129
Posts
909,776
Members
33,623
Latest member
CodyHansen
Top