What have you done to your square lately??

[Vbb199]

Me and a friend were shooting **** the other night over some beer, and i said to him, "would you be interested in some subs and amps?"
He said, sure, ive been wanting to run a setup in my car.

On a set of 12's, 15's, 10's, two 1000w amps and one 1500w amp with a 4 and 8 farad capacitor, i asked him to make me a "lowball offer" .

He replied, 500 ok with you? I said sure. I spent far more on all my stuff, but i need it out of the way.

Last light he came and paid me, got his dough out, and handed me an extra two grants

An early stimulus check!!! Lol

My point in this little story? I'll be buying new balljoints, control arm bushings, sway bar bushings, idler arm, pitman arm, tie rods, coils, and the highly recommended bilstein shocks. Was also wondering if i should get the little u bolts that is part of the upper control arm? Thoughts?

Anyone have the shock length needed for my suburban on hand ? 2wd, 1/2 ton, with 3/4 rear springs.



****anddddd*****



I'll be doing the 4:10 regear starting tomorrow.

 

[Vbb199]

Order is in for all the front end components!

Also------


Speedo gears arrived

You can guess what will be going down this weekend and the next

You must be registered for see images attach

You must be registered for see images attach

 

[Vbb199]

Not fosho if this counts as doing something to my square... but on the way to lunch my seat hinge bolts sheered off......
So i improvised until i fix that

You must be registered for see images attach

 

[CoggedBelt75]

Not fosho if this counts as doing something to my square... but on the way to lunch my seat hinge bolts sheered off......
So i improvised until i fix that

You must be registered for see images attach

Gotta do watcha ya gotta do. And it seems to work.

 

[CoggedBelt75]

Made some time to put front pads on.

 

[Kim Burke]

What's the name of the radiator shop? I'd like to get mine rehabbed too.

Mark’s Radiator Shop
120 Oakwood Ave
Danville IL 61832
217-442-6903

 

[Kim Burke]

Back to Danville,

FIRE INTHE HOLE!

welded up frame, under coated, and the box is hung.

Happy New Year to all!!!!

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[82sbshortbed]

My deep Trans pan came in today along with the overflow bottle. To cold and rainy today to put them on.

You must be registered for see images attach

You must be registered for see images attach

 

[82sbshortbed]

Broke out the paint pen. Ok job. It'll work. Lol

You must be registered for see images attach

 

[Vbb199]

Axle out tonight. Gonna get her tore down and then rebuild tomorrow.

You must be registered for see images attach

 

[Vbb199]

Mo photos

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[Vbb199]

Doesnt look like the fluid has been changed in 100,000,000 years

 

[John Nes]

Picked up a 73 c20 service bed truck over the summer, and finally got a chance to rewore the dash n engine harness , new ignition switch, ditched the regulator for a 3 wire alternator, rewired all the starter wiring...just needed a lil gas in the carb and she fired right up after 20 something years of sittin...Altho it sounds like a sack of hammers is bouncing around the oil n trans pan. Noticed the PO had heavy duty magnets on the trans pan, oil pan, and oil filter...picking up a new drive train for it next week tho!

You must be registered for see images attach

 

[Vbb199]

Picked up a 73 c20 service bed truck over the summer, and finally got a chance to rewore the dash n engine harness , new ignition switch, ditched the regulator for a 3 wire alternator, rewired all the starter wiring...just needed a lil gas in the carb and she fired right up after 20 something years of sittin...Altho it sounds like a sack of hammers is bouncing around the oil n trans pan. Noticed the PO had heavy duty magnets on the trans pan, oil pan, and oil filter...picking up a new drive train for it next week tho!

You must be registered for see images attach

I was wondering when you'd start messing with that

 

[bucket]

Mo photos

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

What the hell kind of stew was in there? Lol