Are my coolant and voltage gauges accurate - where to test

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,121
Reaction score
6,038
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
You must be registered for see images attach

Ive noticed the voltage gauge sticks at 8 or so now a days rather than 12 (or 14 when revving), would sticking my voltmeter on the battery while running and confirming the number is the same tell me gauge accuracy? Or would the voltmeter read higher? I guess I want to know if my alternator/wiring is going bad.

Also, the coolant gauge never goes over 1/4 or so where it is shown when warmed up. thats all warmed up. that seem normal?
 

Goldie Driver

Full Access Member
Joined
Mar 19, 2018
Posts
3,925
Reaction score
6,376
Location
Houston, Texas
First Name
Britt
Truck Year
1980
Truck Model
GMC K1500 Suburban
Engine Size
350
These gauges seem to be fairly accurate in my view, so the voltmeter to me is telling you more than likely a bad alternator. I paid like 36 bux at Advance Auto for a lifetime one, but you may have an OE spare in your pile.:)

The temp gauge seems about right, too. Mine runs at the quarter mark or a needle width or two above after the 195 thermostat opens. Opening is like 3/8 on the gauge and then it falls.

Goldie cools down at idle, too, versus the highway.

The 77 I had seemed like it was always below the quarter mark for temp. I assumed it was a 180 stat, but I was told here that factory was 195 and I don't recall it being changed, so who knows.

The heater worked and the motor never overheated, so no sense in messing with success.

:D
 

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,121
Reaction score
6,038
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Im confident coolant gauge makes sense then. seems strange to not utilize 2/3 or so of sweep.
 

Goldie Driver

Full Access Member
Joined
Mar 19, 2018
Posts
3,925
Reaction score
6,376
Location
Houston, Texas
First Name
Britt
Truck Year
1980
Truck Model
GMC K1500 Suburban
Engine Size
350
Im confident coolant gauge makes sense then. seems strange to not utilize 2/3 or so of sweep.

Yeah, I agree.

On mine the middle mark would probably match the later ones that said 210, and I would probably be pulling over to figure out what the hell.

So, its a happy gauge staying on the left side and the rest is just to make it look like the rest of them.

My 99 Camaro has basically a dummy temp gauge as people apparently complained because the gauge moved around.

No ****, sherlock? A temp gauge needle should move, not just tell you normal until too late, overheat.

:flamingdevil:
 

C10MixMaster

Full Access Member
Joined
Dec 6, 2016
Posts
756
Reaction score
1,420
Location
Kingman AZ
First Name
Ben
Truck Year
1977
Truck Model
C10 BIG10
Engine Size
ZZ4 350
voltmeter and battery voltage should be close. temp gauges came in 3 different ohms ranges if the sender and gauge dont match it wont read correct.

For Truck Years: 1967 - 1973
The Temp Gauge Needle Should Point to:
Left Line (Cold) when sender resistance = 350 Ω
Middle Line when sender resistance = 76 Ω
Right Line (Hot) when sender resistance = 51 Ω
For Truck Years: 1974 - 1978
The Temp Gauge Needle Should Point to:
Left Line (Cold) when sender resistance = 350 Ω
Middle Line when sender resistance = 68 Ω
Right Line (Hot) when sender resistance = 46 Ω
For Truck Years: 1979 - 1990
The Temp Gauge Needle Should Point to:
Left Line (Cold) when sender resistance = 1,365 Ω
Middle Line when sender resistance = 96 Ω
Right Line (Hot) when sender resistance = 55 Ω
 

1987 GMC Jimmy

Automobile Hoarder
Joined
Jan 23, 2016
Posts
5,848
Reaction score
2,387
Location
Mississippi
First Name
Jesse
Truck Year
1987
Truck Model
V1500 Jimmy
Engine Size
350
If your engine bay ground network isn’t right, it can also impact those readouts.
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
2,837
Reaction score
6,356
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
Yes, put your multi-meter on the battery when running the engine. Should read right around 14 volts. (13.9-14.2 V) Engine will not start at 8 volts. Most likely the gauge is bad or has a bad connection somewhere.
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,018
Reaction score
1,811
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
If you take the bezel and clear plastic off the cluster you can then remove the voltage gauge. Multimeter leads will fit into the spring clips behind it and you can check the actual voltage. My bet is a bad gauge.

GM changed electric temp sending units over the years, and finding the right match is challenging. I need the single button wire connection, and the first couple of units I found would barely get the gauge to about 1/4 scale. I also have a mechanical gauge, so I knew it was getting up to 190. I finally found a good match, and now it reads a little more than halfway between 1/4 and 1/2 at 190, and just about touches 1/2 at 200. I think this is a good range. I would have to look at the box to remember which one I finally used.

Also remember that the SBC switched back and forth from 1/2” to 3/8” threads for temp sending units. My GM crate engine has 1/2”, but some original engines from the early 70’s had 3/8” threads. My new aftermarket heads use 3/8”, so I had to move the sending unit to the intake manifold.

Bruce
 

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
5,882
Reaction score
9,623
Location
Washington
First Name
Todd
Truck Year
1986
Truck Model
K20
Engine Size
454
If the truck overheats, temp gauge is wrong.
If the battery goes dead, volt gauge is correct.
Properly Working gauges in a 40 year old unkept beater with a heater are generally a bonus and mostly a stroke of luck.
 

Bextreme04

Full Access Member
Joined
May 13, 2019
Posts
4,135
Reaction score
4,984
Location
Oregon
First Name
Eric
Truck Year
1980
Truck Model
K25
Engine Size
350-4bbl
My 1980 temp gauge with all original gauge, OEM temp thermostat, and I think original sending unit reads dead center on the temp gauge when warm. Volt gauge seems to be accurate too. Like others have said, put a multimeter on the volt gauge connections and see what you get. If it is reading 13v or higher, your gauge is bad. If it reads lower than that, check at the battery. If you see 13v or higher at the battery and 8v at the gauge connections, you have a good gauge, battery, and charging system and just have a poor connection somewhere between the battery and cluster.
 

PrairieDrifter

Full Access Member
Joined
Dec 28, 2014
Posts
3,422
Reaction score
4,482
Location
North Dakota
First Name
Mason
Truck Year
84,79,77,70,48
Truck Model
Suburban k10, bonanza k10, c30 C&C, c10, gmc 1/2ton
Engine Size
350, 350, 350, 350, 350
My volt gauge reads high compared to the actual alternator output, reads almost at the red line at any rpm, I think it reads around 9 at key on. Voltmeter says it works perfect, 14.6 volts

my temp gauge usually hangs out between the 1/4 line and a little bit over the 1/2 line.
 

Latest posts

Forum statistics

Threads
41,857
Posts
903,628
Members
33,370
Latest member
mitchell1128
Top