6 x 9 speaker mounting in door

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Poodlehead

Junior Member
Joined
Mar 23, 2023
Posts
22
Reaction score
18
Location
College Station, TX
First Name
Pat
Truck Year
1977
Truck Model
Silverado
Engine Size
350
I had an older Marantz radio in my 77 Silverado years ago and I was very pleased with the setup until it crapped out. It had 6x9 speakers in the rear of each door and 4.5" in the kick panels.

The door speakers were mounted behind the metal so the lower door panel cover didn't need cutting.

I replaced it with a stock Delco pushbutton radio that was ok for years. Now I'm in the process of getting it refreshed/repaired and wanted to update all 4 8 ohm speakers as well.

My question is concerning mounting the 6x9 in the door. Would it be better to cut the door panels more so the speakers stick out or keep them behind the metal as shown? I really don't want to cut up the lower door panel cover either so leaving them as shown would be better, but is that negatively affecting speaker performance?

Thanks in advance! Pat
 

Attachments

  • PXL_20250518_002006678.jpg
    PXL_20250518_002006678.jpg
    113.6 KB · Views: 10
  • PXL_20250518_001843490.jpg
    PXL_20250518_001843490.jpg
    176.8 KB · Views: 10

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
4,372
Reaction score
8,509
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
Wow, that has to be the worst location possible for speakers. Not only do they take a beating from being on the outside swing off the door, they have to fire thru that so called vent straight into the floor of the cab.
 

Poodlehead

Junior Member
Joined
Mar 23, 2023
Posts
22
Reaction score
18
Location
College Station, TX
First Name
Pat
Truck Year
1977
Truck Model
Silverado
Engine Size
350
Yes, but if you are outside and want to listen to music, all you have to do is open the doors. I agree, the rest of the time, a horrible location to blast music right into the side of your seat :(
 

Catbox

Full Access Member
Joined
Jul 12, 2018
Posts
4,609
Reaction score
17,491
Location
Just Outside of Portland Oregon
First Name
Peter
Truck Year
1979
Truck Model
C20 Silverado Camper Special
Engine Size
461
If you thought it was good enough, run them there.

Personally, they would provide far better performance in the front of the lower door.
At least then they would be firing right into your feet instead of the seat hump.
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
3,391
Reaction score
8,087
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
Another thing to consider, when you block the lower vent, you loose the flow through ventilation these trucks were designed to have.

So you know, newer trucks still have flow through ventilation. The GMT 800's have the vents in the back of the cab.
 

Finkaire

Finkaire
Joined
Dec 28, 2021
Posts
489
Reaction score
816
Location
California
First Name
Loren
Truck Year
1984
Truck Model
Silverado c10
Engine Size
305
Stock location for rear speakers are in the corners with the fronts in the dash. Im not sure about the kick panel application for the front but I think the 6x9’s might work best in the corners. Also if the door panels aren’t already butchered, to leave them alone IMHO
PS. A subwoofer under the seat fills in the low frequencies
 

Attachments

  • IMG_0465.png
    IMG_0465.png
    399.5 KB · Views: 8
Last edited:

Poodlehead

Junior Member
Joined
Mar 23, 2023
Posts
22
Reaction score
18
Location
College Station, TX
First Name
Pat
Truck Year
1977
Truck Model
Silverado
Engine Size
350
Stock location for rear speakers are in the corners
I was not aware that the stock speaker location is in the rear cab corners. That appears to be an excellent location. However, I read about the corner mount speakers and they don't work if your seatbelt retractor is mounted in that area. Unfortunately, my retractors mount in this location (I guess because my truck came with factory bucket seats) so that's not going to work for me. Plus it would cover up my fire ant killer stash.

I still wish I had my buckets, but back in the good old days of being young, dumb, and full of 'it', I needed a bench seat... I will probably stuff some sound deadening material behind the speakers and just call it good where they've been for the past 45 plus years...

Thank you all for the input and suggestions.
 

Attachments

  • PXL_20250520_122708514.jpg
    PXL_20250520_122708514.jpg
    115.1 KB · Views: 8

WFO

Full Access Member
Joined
Jan 6, 2017
Posts
3,927
Reaction score
5,520
Location
Texas Panhandle
First Name
Dan
Truck Year
1986
Truck Model
K20
Engine Size
350
My 6"x9" speakers are mounted in a homemade wood box behind the seat pointing up, and slightly tilted to aim towards the Dome Light.
 

Poodlehead

Junior Member
Joined
Mar 23, 2023
Posts
22
Reaction score
18
Location
College Station, TX
First Name
Pat
Truck Year
1977
Truck Model
Silverado
Engine Size
350
My 6"x9" speakers are mounted in a homemade wood box behind the seat pointing up, and slightly tilted to aim towards the Dome Light.
I like that idea and I bet they sound good with the speakers pointing up to get the sound out from behind the seat.

I've never built enclosures and may be able to find some already built. Thanks!
 

Latest posts

Forum statistics

Threads
45,728
Posts
990,655
Members
38,844
Latest member
Superbonez23
Top