So I have a fun idea to wrap your heads around. Something that popped into my head a while back, and has been rolling around in there for a while gathering dust, haha.
It's not squarebodys specifically, but about any chevy small block in general.
Here it is:
Hypothetically speaking, let's say...
Installed a new 355 I built into my k10 this weekend. Got everything wired up and went to start it and it begins to crank but then will make a loud clunking noise. It will then start to turn over again and do it again. Pulled the starter and checked to make sure it was mating with the flywheel...
Right now, I have an extremely tired 305 and I'm ready to swap it out. Now I've bounced around different ideas, but not sure on which route to take. I think I've narrowed it down to wanting a 350. I don't want to do LS swap or big block. I've done some research and I've come down to:
1. Buy a...
Hello everyone,
I am looking at purchasing a new engine for my '85 K10 as the 305 that was in it is gone. The plan for the truck will be my regular truck to use daily and maybe even take some out of town trips. I want it to be reliable and start every time I turn the key. Originally, I...
Recently engine swapped my 85 C10, took out the stock 305 and put in a rebuilt 350 block with a massive cam and high compression pistons. Of course, my stock quadrajet off the 305 is too small now that she's pushing 300+hp (may seem small to some people on here but I'm excited!). Looking to...
To my understanding, if you get headers for a small block you normally have to do something with the starter (get a smaller one) in order to actually fit headers onto your 350. If this myth is true, are there any good headers out there that i can get for the small block without having to...
Having some trouble with a truck I came across last week. I’m gonna try to make it short and sweet with what I know so far. So, the trucks a ‘85 Sierra w/ the 350 paired with the 4 speed manual. It has an edelbrock 600 carb manual choke. And a micro electric fuel pump pushing 4-7 psi. (I have...
I'm neck deep in replacing the gaskets on my 1987 Silverado Intake Manifold. I'm trying to buy a replacement for the fitting that is shown in this photo. Anybody know what connects here? I'm having a hell of a time explaining it at the parts store. It sits just to the passenger side of the...
Hi!
My name is Ed, and I'm new here. I fell in love with square body's as a kid when my dad bought a K5 Blazer, and that love was reaffirmed later when he bought an '87 GMC Sierra K25. I currently own a '87 GMC R3500 dually. Its and old dump truck (doesn't have the dump bed any more). It...
I've got a 350 engine from a 1981 c1500 that I'm planning on putting in another truck. The engine has 24,000miles on it. The truck it was in was sitting for a few years,but runs awesome and doesn't leak.
While the engine is out, I want to spruce it up and change some seals anyway, should I...
Got an 85 GMC K1500, 305 from the factory, swapped rebuilt 350 in it currently, it's developed a light knock! On start-up it's not there, after about 10 minutes of driving it's really noticeable (audible and feel it under your feet in the driver's seat) when braking. Now it could be that it's...
For Sale: Original 1978 Chevrolet Small Block 350 c.i. V8 RPO code LS9 from from 1978 K20 3/4 ton.
I pulled this engine from my ‘78 K20 in December 2019. It was running well but I wanted a more powerful, more reliable engine so I swapped in a new L31R Vortec 5.7. The engine is the original...
Hey guys,
I'm pretty deep into a restoration on my '93 G20 van. It has a Pathfinder 4x4 conversion with 35s and has a ton of potential, but it needed substantial rust remediation and some body work. Once that is addressed, I'm going to put a new motor in it and have the transfer case rebuilt...
i have a 1981 with the 250 i6 and i want to swap to a 350. i have been able to find that the motor mounts work the same but cant seem to find if my transmission will just bolt up to the 350. i have the 3 speed manual Saginaw transmission and want to keep it. so my question is what will i need to...
I just got a block for a 350 sb, looking to build it to where it’ll put out some decent power for a k10. It’s gonna be a budget build. What are some good heads and etc won’t break the bank, thank you.
I'm installing my intake manifold on my rebuilt 350. Do I need to put gasket seal on the gasket. I hear yes and I hear no. Can someone help me out. Thanks
I have a 79 k10 with a 350 small block. I bought a new mechanical fuel pump, it has three ports, Inlet outlet and the return (I think).Currently my return is plugged. I’ve been having problems with flooding and I’m thinking my fuel pressure is too high, i have a 600cfm edelbrock carb. I bought a...
For my 1983 Silverado, I purchased a 140amp 1 wire alt., and the instructions say to just run a wire straight to the battery. Only thing I'm confused about is how the fuse panel will receive constant voltage. My factory wiring has a output wire from the alt running to the junction block which is...