Search results

  1. S

    Replacement Leaf Springs

    sdtrucksprings.com
  2. S

    New guy from Missouri

    I have a lot of family that work on post. If you hang around the motor pool you probally know them.
  3. S

    New guy from Missouri

    raised up not far from you. plato,mo.
  4. S

    Sm465 question

    use the bushing, bearing is nothing but a waste of time.it wont last.
  5. S

    pulling a engine question

    thanks for all the sugestions, I fiqured it could be done this way. Thanks again, steve
  6. S

    pulling a engine question

    Thanks, I will do that
  7. S

    pulling a engine question

    was wondering if was possible to pull the engine and leave the sm465 and transfer case in the truck. then sit a engine back down in the engine bay and get the input shaft back through the bearing and clutch? Looks like it would be really hard to align it. have done this on several autos. thanks...
  8. S

    Manual Lock Outs

    Just got a set of mile markers at oreilys. Took autos out put new hubs in. Took about 30 minutes. Work well.
  9. S

    Best clutch to buy

    Bucket check your messages please
  10. S

    Best clutch to buy

    No I haven't found one locally yet and I didn't order one off ebay. Gonna look a little more today,then order ebay if I cant find one. Thanks
  11. S

    Best clutch to buy

    Thanks will do!
  12. S

    Best clutch to buy

    found the problem....Broken bell housing.Now i need to find one. been calling everywhere no one has one.
  13. S

    Best clutch to buy

    I have heard good things about the power torque
  14. S

    Best clutch to buy

    Well I was thinking it might just be him also. I drove it a couple of days ago and all was well. Road into to town with him yesterday and it just failed. I had a pressure plate fail years ago in a chevelle. It acts just like that.
  15. S

    Best clutch to buy

    Looking for some advice. I need to put a clutch ,pressure plate,throw out in my sons truck. Stock motor ,sm465,208 case. I put a ASM clutch kit from rock auto,6000 miles ago. It has failed already. Gonna replace tomorrow. What has been some of the better clutches you guys have run. Not sure if...
  16. S

    Manual Swap Help

    I have the pedals,the push rod. I would be wiling to get rid of. you would need the frame bracket, z-bar and the adjusting rod. message me if interested.
  17. S

    spicer locking hubs

    A got a set of spicer locking hubs that came off of a 77 blazer that had a corporate axle. I am trying to install these on a my 79 k10 with corporate axle. I have no instructions and did not get to see them come off the blazer. I have tried everything I can think of and I just cant get them to...
  18. S

    clutch rod question

    Thanks, I do have the boot. I was a little leary of taking a stab at it without some referance point. This will help me alot! Thanks again.
  19. S

    clutch rod question

    I am ready to put my hole thru the floor pan/firewall. The dimple I have been told to look for is not there. Floors were replaced at some point. Could one of you guys that have mechanical linkage give me some measurements from the kick panel or some other good referance point.Where the clutch...
  20. S

    drive shaft questions

    True on junk yards. Trying to find a shop to build me one.thanks for the help
  21. S

    drive shaft questions

    I am in process of changing from 350/203 and going to run sm465/205. Long wheel base. I am having a hard time finding a drive shaft.Before getting a new one built I will check with you all ,and see what suggestions there was. Thanks in advance, Steve
  22. S

    Doing Paintjob At Home

    very good info you have been given. Once you have wiped the body down with the cleaner,do not touch it with bare hands. You will leave behind oil from even clean hands just from your skin. This will cause fish eye. FYI
  23. S

    Doing Paintjob At Home

    I have painted several cars/trucks at home. Besides the body work which you know.Make sure the you wipe the body down with a good wax/grease remover. Blow the bodyoff really well, sanding dust and dirt can hide in the oddest of places. You need to have a really clean place to paint. I have hung...
  24. S

    Blower motor runs only on low

    Thanks for all the info and chart,I did find the problem with mine. It was a bad relay (the second one I tried). Replaced that last night now it is working. Thanks again. Now on to the lift kit.
  25. S

    Blower motor runs only on low

    If the relay is that square plug that bolts onto the AC box,yes I did change that out with one of a 81 truck,still have same issue. I have cleaned all the grounds real good still no change. Put another blower motor,switch in dash,relay in ac box.Still get same results. Broke wire some where...

Latest posts

Forum statistics

Threads
42,129
Posts
909,778
Members
33,624
Latest member
CTGAP
Top