Search results

  1. A

    please help quickly

    I'm trying to sell my truck so I'd rather not put any money into it. But do you think I could weld new perches on at the correct angle and not abuse it till I sell this pig? That would make more sense than getting a new axle. I tried to spin the pinion back with a chain wrapped around the...
  2. A

    please help quickly

    The pinion is point up roughly 15 degrees give or take a degree. Or two.. But I don't know how well you can tell but the perches are rounded fairly significantly actually. Don't think this would cause the pinion angle to still be so severe. Probably doesn't help either
  3. A

    please help quickly

    I understand what your saying but the way I'm picturing it. The pinion would be deflected down and the tubes then spun inside the differential. As the axle wrap twisted the axle back up the pinion had shifted up. At least that's how I see it. I would think if I broke the perch welds I would...
  4. A

    please help quickly

    Yeahhh I know I know.. The driveshaft needs a new yoke welded on because it got so banged up. So I'll get a new u joint when that's done. This u joint is only a couple days old from the last time I lost my driveshaft. Can't thank all of you on this page for your help and patience!!
  5. A

    please help quickly

    I can pick up a ten bolt for 100. I doubt it hurt the locker. I'm just in doubt about biting the bullet and buying a new axle. Idk this kind of shit really sucks when moneys already so tight
  6. A

    please help quickly

    I have a locker in it and when i put the axle in probably 4, 5 months ago the internals on the pumpkin were mint. Obviously fresh fluid, axle bearings and seals. I'm afraid to drive it into the bigger city north of me to go to a 4wd shop. Each time i lost my driveshaft before i was close enough...
  7. A

    please help quickly

    Should i try to bring it back down or drive it like it is then try to pull it down before i have a buddy try to weld it? I'd rather not get a new ten bolt as i have around 500 invested in this one. But they are cheap. Again i'm just not convinced its spun none of the plug welds are broke, the...
  8. A

    please help quickly

    I'd like to if it will help. But I'm afraid there's a bigger issue than putting the blocks in ass backwards. Bucket said i believe that the blocks were installed correctly as in the rear being taller. So there should be no reason why the pinion is angled so high in relation to the driveshaft. It...
  9. A

    please help quickly

    My dad places his magnetic level on the fridge and i don't think its ever been used, but its broke because its constantly getting knocked off. So I can't put a level to it. I have no axle to compare it to either. But should i try to fix the angle with a jack or leave it seeing i can't get it...
  10. A

    please help quickly

    How many plug welds should my ten bolt have? There's three on each tube
  11. A

    please help quickly

    They are one piece blocks and they have been on the truck as long as I've owned it. They were on the old axle and on this one. Should I try to rotate the center section back even if I can't weld it at my house? The plug welds don't look broken. The tubes seem parallel. They don't look spun. I...
  12. A

    please help quickly

    It's a 200 horse 350 I don't know I find it hard to believe I spun the Center section. I understand the angle is built into the blocks but if I put them in backwards it would cause the excessive angle. If I flipped them around so the taller end was in the front it would lower the pinion angle.
  13. A

    please help quickly

    I understand the pinion angle is wrong but I'm wondering if I spun the blocks around if it would be at the correct angle.
  14. A

    please help quickly

    I only ask about the blocks because of the poor pinion angle
  15. A

    please help quickly

    It's still in the transfer case and yes it still has the slip yoke. I don't wheel it enough to justify getting the eliminator kit
  16. A

    please help quickly

    No it has the proper clips but there is a serious vibration coming from the driveline. I got new straps the last time it came out. Oh and they're tight.
  17. A

    please help quickly

    The picture of the block is the right side of rear end.
  18. A

    please help quickly

    I'll be the first to admit I'm an idiot if I can learn from it. But did I install my lift blocks backwards?..
  19. A

    please help quickly

    No leaks. Buttttt I didn't know you could put it on incorrectly?... Which yoke are you referring to? Like the pinion yoke?
  20. A

    please help quickly

    All of the weights are still there. I put another u joint in and new set of straps and bolts. I'm driving but the vibrations are still there. Thinking about getting it balanced Saturday. Transfer case output is good and tight, no wobble there. Pinion yoke on axle is fine too. Don't know what...
  21. A

    please help quickly

    Called a driveline shop shop and they don't think it's a bent driveshaft. But I'm not sure if my shaft is even savable. The end is scraped up pretty good and chip'd a small piece maybe a 1/4 in. out into the recess for the clip.
  22. A

    please help quickly

    It doesn't look bent but idk. The vibrations are speed sensitive. I'm thinking it could be the pinions bent, or the bushing in the tailshaft of the t case is toast. Both times it spit the driveshaft it spit the rear u joint which is a conversion u joint.
  23. A

    please help quickly

    This is the second time in two weeks my driveshaft has knocked out the caps in the u joint and fallen out at speeds. I've experienced drive line vibratuion for a while. I assumed it was the transmission because that's on its way out. But to me the only explanation is my driveshaft is bent and...
  24. A

    Help with finding gaskets pleeeassee

    Either way seems smart im going to try ebay and amazon to see if i can find those sheets reasonably cheap
  25. A

    Help with finding gaskets pleeeassee

    You mean like sheets of that paper gasket not the cork right?

Latest posts

Forum statistics

Threads
41,847
Posts
903,385
Members
33,362
Latest member
Dhatch84
Top