Search results

  1. omillan99

    350 Casting Numbers

    I can't remember what i needed since I bought my flex plate long time ago. You should be fine with everything else.
  2. omillan99

    Tire size for c20 silverado

    BF Goodrich AT KO, Dakotas sold out some time ago also. It seems like BFG didnt makes 16.5 in the new KO2 style.
  3. omillan99

    350 Casting Numbers

    The only things I see that might need more info for would be for the flywheel (might need tooth count, or depending on size of harmonic balancer), manifold (for exhaust if you have headers they might ask if you have square or round port, intake has no difference), and spark plugs (light duty or...
  4. omillan99

    350 Casting Numbers

    "WHOOP WHOOP, Thats the sound of the Police, WHOOP WHOOP." KRS-1
  5. omillan99

    Tire size for c20 silverado

    I bought the last set of 33x12.50x16.5 in the country apparently from Pepboys, not looking forward to getting rims and tires next time around.
  6. omillan99

    Made an accessory fuse block

    Looks pretty sweet, would love to see it installed.
  7. omillan99

    350 Casting Numbers

    The engine was made in 1974 but put into a 1975 vehicle. The amount of interchangeable parts is amazing don't really need an exact model and year, but if you need parts ask for a 1975 full size Chevy car then. If I'm not mistaken Full size is in regards to a cars such as Caprice, Bel Air and...
  8. omillan99

    350 Casting Numbers

    What is getting you confused? What other information are you looking for? What other information are you finding? The info you are putting about the 1974 full sized with a t400 police is what I find all over. Since it was cast and assembled at the end of October it would go for the next model...
  9. omillan99

    350 Casting Numbers

    Based off the info I see and the info I found off Nasty z28 (http://www.nastyz28.com/chevy-engine-code-stampings.php) it is for a model year 1975 the engine was built in October 23 for a full sized pick up. No horse power is listed for this motor.
  10. omillan99

    350 Casting Numbers

    Not sure if yours has it but on the rear drivers side where the bell housing mates to the engine. It wont give you an exact date it was made but it can tell you a range of years.
  11. omillan99

    Help finding a camper top.

    I think that maybe the one I was looking at. Is softopper what it is called?
  12. omillan99

    Help finding a camper top.

    I remember finding a camper type thing that was similar to a soft top on the K5's but for the C/K models. It was also collapsible so you can have it as a tonneau cover have the sides up or the full camper. Does this sound familiar to anyone? Thanks in advance.
  13. omillan99

    Pushrod recommendation?

    Hello everyone, I'm swapping in a 280h Comp Cam into my 400 SBC. I have 1.5 Crane Silver Roller Rocker arms and will be adding in new springs as well. Not sure if this matters but the motor is bored .030 over. How important would it be to get different sized pushrods? Does it make a world of...
  14. omillan99

    Is it safe? part deux

    Perfect thank you for all the info.
  15. omillan99

    Is it safe? part deux

    So just to make sure I understand correctly if I do get the TQ converter done with my stock cam I should be fine to drive it home, then do the cam swap at home? I understand the TQ converter issue which is I want to get the converter in before I swap the cam in.
  16. omillan99

    Is it safe? part deux

    Only because I don't have much space or proper tools to drop the transmission and transfer case.
  17. omillan99

    Is it safe? part deux

    @4WDKC I'm sorry if I made this unclear so when I take my truck to the shop to get the flex plate replaced, I want to get the torque converter replaced also in preparation for the cam. I would then drive it home with the high stall converter about 5 miles with only 3 stops or so. Then I would do...
  18. omillan99

    Is it safe? part deux

    Hello, I'm not the same OP from part one but I had a question and didn't want to hi-jack the other thread. So my question is, can I install a higher stall (I think it'll be in the 2500 to 2800k range, I'd have to report back on that info) torque converter on a mostly stock engine, 33 in tires...
  19. omillan99

    ISO TH400 4x4 Flexplate Cover

    I figured the aluminum ones were stronger than the thin tin ones. I don't beat on it to bad but some of these desert trails have some trash or sometimes detours through brush have to be made. Which is why I'd prefer to use that one instead of having the worry about having no cover or a cheap cover.
  20. omillan99

    ISO TH400 4x4 Flexplate Cover

    Yes, that's what I recall mine looking like. I just don't want any issues since I take it out on the dirt trails and such for something to happen to me while I'm out there.
  21. omillan99

    ISO TH400 4x4 Flexplate Cover

    Perfect, when you compare them would you let me know if they are the same? I have been struggling to find the cast one. A lot of the ones I find are the flimsy chrome ones and only come with four holes. If I remember correctly my had 6 holes for the bolts to mount on to the transmission.
  22. omillan99

    ISO TH400 4x4 Flexplate Cover

    I'm sorry, I know this isn't the correct forum but I don't have sufficient privileges to post in the In Search Of section. Maybe a mod may help. Nonetheless, I have been looking for the metal cover that goes on the bell housing to cover the flexplate with metal rods connecting it and the block...
  23. omillan99

    Help removing radiator support bolt.

    So I got the bolt out. However the support still doesn't move? Am I missing any more bolts? I took 9 off each side. 5 where they meet with the inner fenders, 3 where the wheel well meet, and one next to where the turn signals are. I attached images where the bolts were. It was a total of 18 body...
  24. omillan99

    Front sway bar recommendations

    Not sure if you had fixed your issues with this but ORD has a Disconnect kit to switch between on and off for on-road and off-road use. AFAIK you use your stock sway bar and attach it to the axle. But it does require a minimum of 2 IN of lift which you do have...
  25. omillan99

    Help removing radiator support bolt.

    Sorry for the delayed response. I have tried turning it with a ratchet and socket but it seems to be seized up. Hitting it with a punch from the bottom doesn't seem to push it anywhere. Attached it an image of the other side removed.

Latest posts

Forum statistics

Threads
45,575
Posts
986,734
Members
38,666
Latest member
alwaysbroken
Top