Made a new tool

[Mr Clean]

Well finished building the cart, and got the tools I'm going to have on the back side of the cart....Cart still has to be stripped down and painted....

 

[CalSgt]

Alignment toe tool I made for my Jeep, then adapted it to work on dads GMT400 & my K10

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[89Suburban]

Okay, not mine. I have a press and my bearing separator press, But I like this probably will make one for ball joints and U joints. Yes I have the big c clamp service press but think this will be more useful.

You must be registered for see images attach

I need something like that to crush my beer cans.

 

[CalSgt]

Homemade pinion yoke anchor, holds the yoke steady while you collapse the crush sleeve to set pinion preload. Ultimately turns the floor (or shop bench) into a deadman while you apply the foot Lb's

https://www.gmsquarebody.com/threads/80-k-10-squircle-build.34732/

You must be registered for see images attach

 

[CRM]

This is my hack valve lash adjustment tool.

You must be registered for see images attach

 

[CalSgt]

Custom bandsaw for making perfect cuts in exhaust U bends

 

[CalSgt]

Custom bandsaw for making perfect cuts in exhaust U bends

Couldn't get the photos to load last night

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[AyWoSch Motors]

Made this one a while back.

Anyone guess what it's for?

You must be registered for see images attach

 

[78C10BigTen]

Made this one a while back.

Anyone guess what it's for?

You must be registered for see images attach

Jumping "shorting" the 2 terminals on a pre obd gm car?!

 

[78C10BigTen]

Made this one a while back.

Anyone guess what it's for?

You must be registered for see images attach

Otherwise a "fish can key" for opening old school door knobs? Lol

 

[AyWoSch Motors]

Jumping "shorting" the 2 terminals on a pre obd gm car?!

Yessir, homemade diagnostic tool for jumping the A and B terminals on an OBD1 port, to rear the trouble codes.
Works great on 87 to 95 chevy trucks, and is slightly less cheesy than a paper clip.

 

[84-C20]

Yessir, homemade diagnostic tool for jumping the A and B terminals on an OBD1 port, to rear the trouble codes.
Works great on 87 to 95 chevy trucks, and is slightly less cheesy than a paper clip.

Back in the day there was a flat metal thing made like a key for jumping the ALDL, complete with hole to put it on a key chain, they may well still make them IDK. I didn't like the idea of paying for one so I made one, actually I made 4 of them, enough for each mechanic in the shop to have one. I have no idea where mine is, or even when I last saw it, but your post reminded me of it.

 

[84-C20]

This is my hack valve lash adjustment tool.

You must be registered for see images attach

I have always hated adjusting valves. It's not that I don't know how to do it, I just find it tedious, mostly because I tend to get overly anal about where the engine is at even though I know all that really matters is that the valves being adjusted are shut. This is a REALLY good hack and would give me the visual my mind would like.

 

[Blue Ox]

Yessir, homemade diagnostic tool for jumping the A and B terminals on an OBD1 port, to rear the trouble codes.
Works great on 87 to 95 chevy trucks, and is slightly less cheesy than a paper clip.

I was going to guess circuit breaker tester.

 

[C10MixMaster]

homemade distributor machine

You must be registered for see images attach

You must be registered for see images attach