What new tools have you got lately?

[Camar068]

Hmm well aren't you fancy,too good to take out a drain plug with a combination wrench.Hmm,maybe you need an impact,you don't even have to turn it. I hope you know I'm just kidding,an impact would strip an oil pan,but you could still use it to take them out,save 1/2 the energy.

lol agree. Working on medical equipment, I can always tell who's lazy with the drill. The screws are half stripped and way too tight, or have been changed to a different screw.

Right tool for the job.

 

[Terlingueno]

Well, since I began my maintenance/fixin stuff/tool inventory and it is pretty much done, I discovered that my vacuum test gauge was missing in action. Couldn't find it in any box, container, bag, or anywhere else it could be. So I found a USA made replacement for less than $50 on "that auction site". Tested this morning, works like it's supposed to.

You must be registered for see images attach

 

[legopnuematic]

I’ll be picking these up at the end of the month from a friend.

24x36 TruStone surface plate and stand (they make Starrett surface plates)

You must be registered for see images attach

And this C.R. Onsrud inverted pin router, model 2003.

You must be registered for see images attach

$500 for both, I figure is a pretty good deal.

 

[waterpirate]

I have a similar coil nailer bought in 2017ish. It’s one of the few tools that is actually justifiable to purchase for a single job. Nailing 20 squares of comp shingle down by hand sucks.

You must be registered for see images attach

Not a roofer, but put a new roof on my brother’s house and a shed for my dad.

They work great for flashing as well.

I bought a coil nailer at horrible freight to do 1 1/2 square on my shed. lol Does that mean I am lazy?
Eric

 

[Frankenchevy]

I bought a coil nailer at horrible freight to do 1 1/2 square on my shed. lol Does that mean I am lazy?
Eric

Nah, just better at justifying

 

[1STLS1]

Bought this a couple weeks ago, it's a coolant exchange machine. It pulls old coolant out, applies a vacuum to the system, then installs the new coolant.

You must be registered for see images attach

Scored this also a while back but have not had time to play with it, a old school GM Tech 2 with OBD1 stuff

You must be registered for see images attach

 

[89Suburban]

Bought this a couple weeks ago, it's a coolant exchange machine. It pulls old coolant out, applies a vacuum to the system, then installs the new coolant.

You must be registered for see images attach

Scored this also a while back but have not had time to play with it, a old school GM Tech 2 with OBD1 stuff

You must be registered for see images attach

I want one of those Tech II's so bad for my truck.

 

[TotalyHucked]

Picked up a DeWalt 1/2" combo at Ace Hardware yesterday to replace the one I have misplaced...still need to replace the ratcheting one. They're in this damn shop somewhere but I haven't found them in 6mo of looking lol

 

[Sad Sack]

Picked up a DeWalt 1/2" combo at Ace Hardware yesterday to replace the one I have misplaced...still need to replace the ratcheting one. They're in this damn shop somewhere but I haven't found them in 6mo of looking lol

They'll be in the last place you look.

 

[idahovette]

You'll find it SOON!!!......DAMN, now @Sad Sack beat me.......I'm out

 

[Sad Sack]

You'll find it SOON!!!......DAMN, now @Sad Sack beat me.......I'm out

I do computer support and multi-tasking is easier done when I'm dealing with those who lied on their resumes.

 

[idahovette]

I DIDN"T LIE ON MINE????!!!!!! damn I got in

 

[waterpirate]

Picked up a DeWalt 1/2" combo at Ace Hardware yesterday to replace the one I have misplaced...still need to replace the ratcheting one. They're in this damn shop somewhere but I haven't found them in 6mo of looking lol

When you find it can you see if my 10mm wrench is with it?
Eric

 

[Sad Sack]

I DIDN"T LIE ON MINE????!!!!!! damn I got in

Uh.....I mean the ones that call into my line, not the ones on-line lol.

 

[TotalyHucked]

When you find it can you see if my 10mm wrench is with it?
Eric

I'll keep my eyes peeled!