LS swap cost - COMPLETE a-z Drive in, drop it off & pick up tuned and perfect.?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Jwernatl

Full Access Member
Joined
Oct 5, 2020
Posts
190
Reaction score
127
Location
Senoia, GA
First Name
John
Truck Year
1987
Truck Model
V10
Engine Size
5.7ltr
Guys - I know this is loaded question -

BUT - in your opinion, what is a fair cost range to have a reputable shop perform a COMPLETE LS SWAP into my 1987 V10? Keeping my 700R4?? or swap that too?


Let's say…the donor engine has less than 50k miles, perfect running engine - no need for a tear down. (should we at least replace the cam? I'll be pulling a camper (maybe) cross country in next 5years)

I will drive it everyday with cold AC, hot heat, good fuel milage, plenty of power and reliability.


**I would want the shop to supply the donor LS, fuel, harness sensors - etc etc
- COMPLETE A-Z - the whole shooting match.**

Just your opinion -

what is fair cost range at your location? - please list if you will

What is best LS?

What is least expensive LS?


factory exhaust set up - nothing crazy


I have the 700R4 (probably just keep that - if it's possible)



 

82sbshortbed

Fuckemall!!
Joined
Mar 1, 2018
Posts
14,646
Reaction score
48,561
Location
SE Texas
First Name
Doug
Truck Year
1982, 1984
Truck Model
1500 shortbed, 1500 longbed
Engine Size
454, 305
More than you wanna spend I bet.
 

TX87R10

Full Access Member
Joined
Jun 25, 2020
Posts
973
Reaction score
2,000
Location
Texas
First Name
Patrick
Truck Year
1987
Truck Model
R10
Engine Size
305
> I would want the shop to supply the donor LS, fuel, harness sensors - etc etc - COMPLETE A-Z - the whole shooting match.

If you are having a shop do this I would consider how long you can afford to not have your truck when / if something goes wrong.

> What is least expensive LS?

Not a great way to approach a very expensive swap :)
 

Jwernatl

Full Access Member
Joined
Oct 5, 2020
Posts
190
Reaction score
127
Location
Senoia, GA
First Name
John
Truck Year
1987
Truck Model
V10
Engine Size
5.7ltr
LS swap. Woohoo. :welcome:


Yes, this is still under consideration - But, I think I would like the reliability and power ease.

I can't find anyone local that is able to do this.
 

climb-101

Full Access Member
Joined
Mar 12, 2018
Posts
262
Reaction score
278
Location
montana
First Name
seth
Truck Year
974
Truck Model
c2 crew cab
Engine Size
6.0 LS
here is my guess

$1500 motor
$1000 fuel setup now lines/fittings/pump
$1000 AC setup
$1000 BP harness/program computer ( wouldn't mess with cutting down an old harness)
$1000 miscellaneous things like fluids motor mounts, charge the AC, ECT.
???? labor - im guessing it would be around $5000 to the shop do the swap

Around $10K im guessing.

i did a 6.0/4l80/NP205 setup in my crew cab and love it.
 

Jwernatl

Full Access Member
Joined
Oct 5, 2020
Posts
190
Reaction score
127
Location
Senoia, GA
First Name
John
Truck Year
1987
Truck Model
V10
Engine Size
5.7ltr
here is my guess

$1500 motor
$1000 fuel setup now lines/fittings/pump
$1000 AC setup
$1000 BP harness/program computer ( wouldn't mess with cutting down an old harness)
$1000 miscellaneous things like fluids motor mounts, charge the AC, ECT.
???? labor - im guessing it would be around $5000 to the shop do the swap

Around $10K im guessing.

i did a 6.0/4l80/NP205 setup in my crew cab and love it.

$10k I can do that.

You guys think it would devalue a 'stock' clean V10?
 

climb-101

Full Access Member
Joined
Mar 12, 2018
Posts
262
Reaction score
278
Location
montana
First Name
seth
Truck Year
974
Truck Model
c2 crew cab
Engine Size
6.0 LS
$10k I can do that.

You guys think it would devalue a 'stock' clean V10?
nope, I would think it would help the value, its not some rare truck that originality add to the value
 

Bextreme04

Full Access Member
Joined
May 13, 2019
Posts
4,135
Reaction score
4,984
Location
Oregon
First Name
Eric
Truck Year
1980
Truck Model
K25
Engine Size
350-4bbl
You have the best possible donor since it already has the fuel lines and EFI tank. Fuel system is as simple as replacing the TBI fuel pump with an AC Delco EP381 which is <$150. No need to replace any other line. Standalone harness is only $250. You can run an LS and 4L60E(exact same trans as your 700R4 externally) with a 0411 ECU that can be programmed for free with a $60 tool. You can buy them with a factory tune and VATS/rear O2 delete for $150 all-in. For just a simple LQ4/4L60E in an 87, you should be able to be well below $10k if the shop knows what they are doing. You shouldn't have any trouble finding a shop that specializes in LS swaps in GA.... or anywhere in the south really.
 

Doublenaughtspy

Junior Member
Joined
Feb 20, 2014
Posts
11
Reaction score
10
Location
ATL
First Name
Paul
Truck Year
1984
Truck Model
K10
Engine Size
350 cid
Yes, this is still under consideration - But, I think I would like the reliability and power ease.

I can't find anyone local that is able to do this.
There is a shop in Marietta, GA that will do the swap. With a 5.3L donor (including the pedal and ECM), headers, wire harness, fuel system, mounts, tuning...it'll be around $7-8k. Generally a 5.3L at around 100k miles is an easy find. You CAN use the 700r, but if you have a later model drive by wire donor, a method of hooking the TV cable for your transmission to the accelerator position will be tough (read that "cost more to figure out"). Better to go with the 4L60E or make sure you get an early 5.3L that is cable operated throttle. BUT that means more likely a higher mileage donor motor and that TV cable is very sensitive to proper adjustment. A 4.8L would likely be a little bit cheaper, but I wouldn't cut that corner on such a big expense. Yet another consideration is to find a 5.3L with the original transmission for the swap. That opens another can of worms on whether you want the 6L80 or 8L80 transmissions that we've heard so much trouble from......not at all an easy question.
 

Craig Nedrow

NADAR UNDER THE RADAR
Supporting Member
Joined
Sep 1, 2018
Posts
823
Reaction score
1,459
Location
Washington State
First Name
Craig
Truck Year
1973 (have two), 1985
Truck Model
K10, K20, C20
Engine Size
350, 454, 6.2 Detroit
Bought a LQ4 with a 4l80e out of a 1999 2500 pickup for 1500 bucks. Has an 896 controller, which I will use, complete un cut harness. The 411 controller has more memory? than the 896, but the HP MP3 tuner works excellent on the 99 Camaro with the 496 controller. Parts for the motor:p

You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach
 
Last edited:

77 K20

Full Access Member
Joined
Nov 9, 2012
Posts
3,075
Reaction score
3,044
Location
Montana
First Name
Mike
Truck Year
1977
Truck Model
K20 5" lift
Engine Size
HT383 fuel injected
Check out Tilden Motorsports. They offer take out engines that are tested with a 1 year warranty, a pre-flashed ECM and a custom wiring harness, fuse block, all accessories.

$2,200 for the 4.8L
$3,000 for the 5.3L
$3,950 for the 8.1L

Other engines available. 6.0, 6.2...

http://tildenmotorsports.com/products/take-out-engines.html
 

TubeTruck

I'm from Boston. Deal with it.
Joined
Sep 4, 2019
Posts
1,417
Reaction score
2,135
Location
East TN
First Name
Denis
Truck Year
1978
Truck Model
Suburban K10
Engine Size
LQ9
It depends if you have friends, how long you want to wait for your truck, etc. I paid $800 for a 126k mile LQ9 with no accessories and an LS3 oil pan, found a guy on marketplace selling accessories, LQ4 oil pan, LQ4 pistons and rods, and a pile of other parts for $100. I'm sure I'll make $3-400 back on the extra stuff I got. Reworked the factory harness, my buddy sent me a 6106 pcm so I could use the factory a/c. Using a 4l80e I pulled with a 7400, which after sales from the truck was basically free. Once I sell the engine and transmission from my truck I'll be into this LS swap for a grand or less.

I never use a shop so I couldn't tell you about that but if you gather all the parts it will be considerably cheaper.
 

Latest posts

Forum statistics

Threads
41,851
Posts
903,497
Members
33,365
Latest member
rossivey
Top