Search results
-
no power to starter/wiring issues
I need steps on how to troubleshoot no power to the starter soleiod. bare with me because i do not have the best technical vocabulary when it comes to this stuff. i have begun the process completely re-wiring my sbc with the original wiring harness, at this point in time all i want to do is get...- devin bianco
- Thread
- k10 neutral safety switch sbc sbc350 small block 350 starter starter ignition starter soleniod wiring wiring harness
- Replies: 12
- Forum: Engine & Performance
-
small block oil to rocker arm issues
my exhaust rocker on cylinder one is receiving no oil when the oil pump is getting turned over. its a brand new crate motor, im assuming the oil passage is blocked. what's the best way to clean that passageway? edit: i've tried plugging all other holes on drivers bank and running at 60 psi for...- devin bianco
- Thread
- 350 5.7 help no oil to rockers oil issues oil to rockers sbc sbc 350 small block
- Replies: 6
- Forum: Engine & Performance
-
Dana 44 overhaul...2 different spindles?????
So long story short, i tore apart my 1979 k10 dana 44 front axle that was stock as far as i knew. ordered ball joints U joints and bearings. i got my ball joints in, U joints in but ran into an issue with the spindles. My driver and passenger spindles where noticeably different. the new bearings...- devin bianco
- Thread
- 4wd axle axle shafts dana 44 help k10 rotor spindle spindle bearing
- Replies: 2
- Forum: Differential & Driveline
-
AXLE SHAFT HELP!!!!!
Doing U joints on my 1979 Chevy k10 pickup with a Dana44 spicer axle. Axle shafts came out fine but after I installed new U joints the bearing caps would not fit through the knuckle. The actual CV housings will fit without the U joints in, but after instal the bearing caps stick out to far to go...- devin bianco
- Thread
- Replies: 19
- Forum: Differential & Driveline
-
quick question, full time to locking hubs (k10 10 bolt)
I am doing the 203 to 205 swap on my 79, soon enough the front axle is going to be rebuilt and i know i will need t install a manual locking hub kit (currently has no hub locking mechanism). when i look it up, all i see is part time 203 kits that include the hubs. In this case will i just need a...- devin bianco
- Thread
- 1/2 ton 10 bolt axle k10 manual locking hubs np203 np205 part time
- Replies: 2
- Forum: Differential & Driveline
-
Np203 to Np205 , transfer case swap
this might have been talked about before, but it would be nice for some clear information on it. first here are some specs: Ive got a 79 k10, sb350 going to a th350 going to a np203 full time no slip yoke. we are doing a np205 swap, we have the truck down to frame with no current drivetrain...- devin bianco
- Thread
- driveshafts help linkage np203 np205 np208 swap t-case th350 transfer case
- Replies: 24
- Forum: Transfer Case
-
Seats, difference from 81-87 and 73-80
Im looking for a seat cover from USA1 industries, the seat says its for 81-87 and its going on a 79 (tilting back) I like it because its the cheapest Just wondering if this was just a fabric or cloth design thing, i don't care about it being original. Or if its a minor enough difference that it...- devin bianco
- Thread
- 73-80 81-87 interior seat seat cover
- Replies: 13
- Forum: Seats
-
Overhead tonneau cover?
Who here knows where i can get a tonneau cover like this?- devin bianco
- Thread
- accesories cool stuff cover offroad overland overlanding tonneau tonneau cover tonneu tonneu cover
- Replies: 24
- Forum: Aftermarket Accessories
-
First truck, first restoration. Should be fun. 1979 Scottsdale k10
Hi I’m Devin I’m a 15 yr old kid outta Wisconsin and I’ve got a 79 Scottsdale k10 project. My grandpa bought it new in 79 and told me either I can have it or it’s going to the junkyard lol. Here’s the truck Well that was back in 79... here is now— well a few months ago. Body is pretty...- devin bianco
- Thread
- 1979 restoration square body truck build
- Replies: 45
- Forum: Introduction
