Search results

  1. Dodg3m4n

    What have you done to your square lately??

    I threw some tools at it and it decided to start finally!! but seriously I just installed headers and wanted to be included to see how far behind I am on fixing it up
  2. Dodg3m4n

    I think I need a new engine

    I got almost all the loose ends tied up and test drove it just a bit ago and it seems to be much happier now. I wasn’t able to get a timing light so I haven’t messed with the distributor timing yet either. Now my issue is where to route the starter wires so they don’t met or burn.
  3. Dodg3m4n

    I think I need a new engine

    Sounds to me like I’m picking up a timing light when I get paid again. Do I really need one of the $100 ones or would the $30 one I found be okay to use? It definitely needs new parts but they get a little expensive. Also I’ve found conflicting information about what type distributor I have so...
  4. Dodg3m4n

    I think I need a new engine

    And those marks are the points on the metal plate that lines up with the groove in the balancer right? If so does that plate have the degrees on it to tell when it’s at a certain point?
  5. Dodg3m4n

    I think I need a new engine

    How would I go about verifying the timing? I know it could probably be tweaked a little one way or another. How would one change the position of the advance unit and how would that help? I’m sure if it advances it to far or not enough it’ll run but just really bad right? How does the vacuum...
  6. Dodg3m4n

    I think I need a new engine

    I do have one thing that is bugging me though. Obviously the exhaust gets hot but would they get hot enough to burn the oil off the engine block? It’s smoking pretty good from the engine behind the headers. More than it did with the factory logs on. My valve cover gaskets are toast so that’s...
  7. Dodg3m4n

    I think I need a new engine

    I finally got it started!!! I’m not sure what I was expecting but it was definitely not to make myself deaf just by sticking my head under the hood with it running. Now I believe all my issues are the oil leaks from everywhere. I saw your reply after the fact but I moved all the wires one spot...
  8. Dodg3m4n

    I think I need a new engine

    I found that same image a few days ago and the wires get pulled super tight and one or two of them won’t even reach from distributor to plug. I started with number one where the rotor is about to be. Should I try moving them all one spot over and see what happens?
  9. Dodg3m4n

    I think I need a new engine

    that is the vacuum advance right?
  10. Dodg3m4n

    I think I need a new engine

    Went and bought jumper cables because I seem to have misplaced the ones I had but it’s trying to start now and some cranks it keeps rolling for a second or two after I stop cranking. Maybe the battery needs a good charge on it before it’ll run? I can hear it trying to fire listening to the open...
  11. Dodg3m4n

    I think I need a new engine

    It’s pointing directly at #2 cylinder. Should I put the cap back on and start with #1 plug wire there and work my way around?
  12. Dodg3m4n

    I think I need a new engine

    Sorry for the blurry photo but which of those points should the line be at? I just want to make sure I have it set up properly
  13. Dodg3m4n

    I think I need a new engine

    I don’t have anything to catch it in but it’s all evaporated now. There’s marks on the frame where it spit out but nothing left and no more is coming out. I checked the coolant and oil and there isn’t one in the other so that narrows possible problems down right? Or is that wrong thinking
  14. Dodg3m4n

    I think I need a new engine

    It cranks freely without the spark plugs but it’s shooting some kind of liquid out number 6 spark plug hole. It smells like gas and something else mixed together. I don’t have a helping hand so I can’t really verify anything in the engine bay by watching when I crank it over
  15. Dodg3m4n

    I think I need a new engine

    I had one until someone decided they wanted my stuff more than I did. Never used it though. How would the vacuum gauge be handy on my old work truck?
  16. Dodg3m4n

    I think I need a new engine

    Octane- that was the first thing I checked because it leaks oil from any and everywhere it can. Mtnman- I will definitely try that first thing tomorrow morning and see what happens. And now that I think about it it’s been hard to start after a drive of any amount. Wether to Taco Bell on the...
  17. Dodg3m4n

    I think I need a new engine

    I haven’t pulled the distributor out though is what’s puzzling me. I’ve only removed the cap and I have it marked so it goes back to the exact same spot. It was running mostly fine before the log split and header install. I don’t know exactly what headers I got but all passenger side plugs I can...
  18. Dodg3m4n

    I think I need a new engine

    I may have done it dumb then because I got to TDC by feeling the compression and pooped the cap off to see where it was pointing and put number one where it was about to spin to
  19. Dodg3m4n

    I think I need a new engine

    And this is why I came here because that thought didn’t even cross my mind. I will have to try that then it’s not raining here. But I do know it don’t do anything with spark plugs in. I forgot to say this earlier but it’s a stock LS9 350
  20. Dodg3m4n

    I think I need a new engine

    I’ll try to make this short and to the point to save some time. The stock logs split so I installed headers. In doing so I pulled off a few spark plug wires from the distributor. In a stroke of genius I thought it might be a good idea to replace them and in doing so forgot where they went or how...
  21. Dodg3m4n

    Headers on 350 with SM465 2WD

    Catbox do your headers go under the Z bar? Ground clearance will only be an issue if I lower it but that’s a discussion for a different day. And for todays dumb question of the day, would I drop them in from uptop or from the bottom up?
  22. Dodg3m4n

    Headers on 350 with SM465 2WD

    I don’t remember and I’m not at my storage spot to see if it is two or three sets. I know 2 sets for sure and I know one set came of an auto C10. I’m not above putting dents in them to fit I’m just worried about having enough room for the clutch linkage. Thank you everyone for the replies
  23. Dodg3m4n

    Headers on 350 with SM465 2WD

    Hi everyone! I’m new here and this is my first post. I’ve been doing some research and haven’t found exactly what I’m looking for or maybe I did and just read past it. My father in law gave me two or three sets of long tube headers for a small block but I have no idea what they are supposed to...

Latest posts

Forum statistics

Threads
42,207
Posts
911,357
Members
33,708
Latest member
btrain04
Top