Search results

  1. geolee

    My brand new pre-owned Chevy

    Just got a 94 short bed standard cab Chevy after I got done with the 84 c10. I did a little preventative maintenance and ended up getting bad parts from oriellys. Spent over a week trying to figure it out. After I got it driving home the check engine light came on so next day I hooked it up to a...
  2. geolee

    700r4 dipstick broke in half

    Was going to go for a ride and checked the trans fluid before I was about to leave and when i pulled out the dipstick it broke towards the end close to the full mark. Anyone else had this happen?
  3. geolee

    Perfect time

    I been messing with my 92 350 trying to figure out where it runs the best I put a new edelbrock intake and carb. Msd distributor and wires, new cam/lifters, gear drive and electric fuel pump. Seems like everything you read or hear is different lol. What do you all run on ur old small blocks?
  4. geolee

    Recent pics of my 84

    Since this virus has been around I been working non stop on my truck. Just got done doing a new cam, gear drive, new exhaust, new dizzy, tires, front bumper, and couple other things. It sounds awesome and enjoying it as my daily driver
  5. geolee

    What torque convertor would be best

    My 84 C10 came factory with a 305 and I swapped it out for a 1992 350 that I put a mild cam and gear drive in. It has the stock 84 700r4 and convertor. I have a 92 700r4 with a stock torque convertor that came with it and was matched to a 350. Should I get a new convertor? I'm going to rebuild...
  6. geolee

    Thread stripped in rear cylinder

    So recently I put a new cam and lifters in and when I went to put the very rear drivers side intake bolt in and torque it the bolt just started spinning so I stopped and left it. Got the cam broke in and then noticed the leak after. It's not real bad but need to fix it. Wondering what everyone...
  7. geolee

    Priming oil until it comes out of rockers 5.7 1992 engine

    So put a new cam and lifters in yesterday I adjusted all the lifters and put oil in the engine and went to prime until oil comes out of the rockers and only got oil to come put of the drivers side. I was using a cheaper priming tool that I got from. Summit for like $20. I'm thinking the tool is...
  8. geolee

    Adjusting new hydraulic lifters 92 5.7

    I put a new cam and lifters in and first time adjusting them. Can you guys give me some advice on how you do it? I haven't ever put a new cam in and don't want to ruin it. Thanks in advance
  9. geolee

    84 with a 92 5.7 cam swap

    I'm going with a comp cam hydrualic flat tappet and new lifters. I'm curious how you guys adjust them before breaking the cam in. First time for me doing this and I've seen a bunch of different ways that people do it and don't want to mess anything up. The motor was running good before I just...
  10. geolee

    1992 carbed sbc cam swap

    So I bought a lunati cam a while back like a couple years and decided I would finally put it in and it will not slide in at all and I don't wanna force it in. My stock cam isn't bad but I wanted a new cam and no warranty on this one. I even tried sanding it down to fit the bearings and no luck...
  11. geolee

    My garage... chevy's & harleys

    its hard to work when you have bikes sitting next to you and then have alot to do to the 53 in the backround after im done with the 84. then the first bike needs a top end. i will never be bored lol
  12. geolee

    Just found this site on the internet today.

    I have a 84 c10 and put a 92 5.7 in it myself and pretty much done. Have to run a electric fuel pump cause the block isn't machined all of the way for a push rod. Then some wiring and should be on the road again. Sucks to not be able to use a mechanical pump. I'm sure someone here has ran into...

Latest posts

Forum statistics

Threads
42,178
Posts
910,766
Members
33,673
Latest member
jcuriel512
Top