Search results
-
K5 Blazer repaint cap body color or white? How to remove fading paint on fiberglass.
You're right about it being harder. Im a painter so I'm probably a bit more set up for it than others. Not a car painter mind you (cabinets, conv varnish, lacquer, stains, dyes, custom front doors, log cabins) but most of it including the equipment crosses over. Most the time I prefer a 2... -
K5 Blazer repaint cap body color or white? How to remove fading paint on fiberglass.
@TDoc That's fair. I use it to remove anodizing and have seen what it can do to some aluminum so I was just putting a warning out there, glad you had good luck with it. -
K5 Blazer repaint cap body color or white? How to remove fading paint on fiberglass.
Was going to recommend gelcoat but thought it would be considered too labor intensive for most here. OP, be careful with that oven cleaner around aluminum -
Show off your non-square project cars.
Yep it's got those seats. Leather, fake walnut, Bose sound, OnStar, tint, power everything including moonroof ...They pretty much through the kitchen sink at it. They went for like 30k right up next to the Blazer that was only 15k or something like that.- Jawzjeep
- Post #25
- Forum: Other Vehicles
-
2in lift with a soft ride
I've been considering swapping out my 6" tuff country HD springs for some 4" ez rides for the same reason, softer. Please report back!- Jawzjeep
- Post #2
- Forum: Lifted & Off-Road Systems
-
-
Show off your non-square project cars.
This is my current project. Not the one I want but the one I need. It's name is Project Daily. I picked this thing up last year for $500 running and driving needing tlc to use as a flipper. I've got $1,300 into it now. I quit my job on friday that I had for 17 years with a company vehicle...- Jawzjeep
- Post #17
- Forum: Other Vehicles
-
Kick panel Speaker Mounts
Add a crossover and get rid of the base out of those speakers In another vehicle I used a thick coat of elastomeric on the back of the panel which helped a lot... good luck- Jawzjeep
- Post #16
- Forum: Stereo & Entertainment Systems
-
New to the site
Nice Calico Chevy Hello from the great north wet.- Jawzjeep
- Post #13
- Forum: Introduction
-
Dana 60 front brake hoses with prebent caliper end?
Alrighty I'm just going to go with it then. If I didn't already have brand new Crown hoses I would probably go with the AN setup. They're pretty nice. Thanks -
Engine woes
Check your coolant temp sensor while you're at it. When mine was bad it would work fine for a few minutes and then act stupid. Good luck.- Jawzjeep
- Post #7
- Forum: Engine & Performance
-
Dana 60 front brake hoses with prebent caliper end?
Nothing on either one of the hoses comes apart. This is my crown hose on the left and what I took off the Dana 60 when I got it originally on the right. -
Dana 60 front brake hoses with prebent caliper end?
Just put a Dana 60 in the front of my 91 Suburban. The factory brake hoses that were already on the axle had a 90° metal end in the hose where it met the caliper. The stainless wrapped extended brake hoses I have on the burb already will bolt to them but don't have that metal 90° bend in them... -
General Spring of KC
I agree. Good price for the stuff I got too I got some Wagoneer Springs from them for my YJ. When I asked them if they would add a military wrapped second Leaf they said they couldn't though.- Jawzjeep
- Post #6
- Forum: Suspension, Steering & Brakes
-
Planning my Suburban build - Advice wanted
My 91 has a tuff country EZ ride 6" all spring lift with 37's and I still had to tastefully trim my fenders. Heavy rear tire carrier bumper and winch bumper up front made it worse. Sliding that front axle forward an inch would help with the firewall side. And count me down for another vote...- Jawzjeep
- Post #20
- Forum: Suspension, Steering & Brakes
-
Dana 60 BOM # confusion
Thank you folks I appreciate it. Not sure why I couldn't find that, dang it.- Jawzjeep
- Post #11
- Forum: Differential & Driveline
-
Dana 60 BOM # confusion
I'm more interested that the number doesn't show on any of the sites that list BOM's I checked. No oil in it, no knuckles or gears. All that can change. I've got another place I can check. They're a little irate at times but I'm sure I'll get an answer.- Jawzjeep
- Post #4
- Forum: Differential & Driveline
-
About to get my first cummins truck.
Well that was short-lived. Sold the truck to a friend. The poor guy has been hauling firewood, elk hunting and towing stuff with a mid 2000's Chevy quad cab 1500 ( we call them half ton hanky box's) for the past few years. I felt so bad for him that I HAD to sell him a real truck. Really...- Jawzjeep
- Post #26
- Forum: Other Vehicles
-
Dana 60 BOM # confusion
Got a 60 front I'm going to pull out from the pile and start getting ready for the burb. Was doing nothing and looked up the BOM and can't find it on multiple websites, even BillaVista. What I read is 610033-2 Even tried 0038, 0088, 0083... Anyone?- Jawzjeep
- Thread
- Replies: 11
- Forum: Differential & Driveline
-
-
About to get my first cummins truck.
The Tempo leaked so much oil that the ferry service here wouldn't let me get on. It was so oddball that it was kinda cool though. It would move forward from a stop in any forward gear except 5th.- Jawzjeep
- Post #22
- Forum: Other Vehicles
-
About to get my first cummins truck.
My uncles place. If I ever build a place a full wrap around porch is mandatory. Especially here in the Great North Wet. There's never enough dry covered area.- Jawzjeep
- Post #21
- Forum: Other Vehicles
-
About to get my first cummins truck.
Got it running today. Replaced the 2 lines and got the air out. A lot easier than I thought. Just overcomplicated it. Appreciate the help folks- Jawzjeep
- Post #14
- Forum: Other Vehicles
-
-
About to get my first cummins truck.
@legopnuematic it's a slushbox. I've already been warned about using ether so I won't be doing that. Time to go read up on the VP 44. And I'll definitely check out your thread, thanks.- Jawzjeep
- Post #10
- Forum: Other Vehicles
