Search results

  1. 8

    rebuilt engine dead #3 cylinder

    hey guys, so i rebuilt my 355 this past winter. it was my first complete rebuild but i did it the right way, total macheine work ffrom top to bottom, its a 355 with flat tops, 882 heads,comp cam max lift 444 and stock compression. The truck hasnt been drivin, i cant drive it in my area and...
  2. 8

    DOUHHH!!!! dent in fender

    thank you!!
  3. 8

    DOUHHH!!!! dent in fender

    i had one of my junk doors fall over today and put a quarter size dent in my GOOOD fender. The dent is on the body line. it pushed it down a bit, and i am wondering how i would go at poping that out. again its on the crease of the body line
  4. 8

    cab corner and door gap

    iv got a good set of doors!! that door is striaght its just got that one hole hahah. its accualy a decent door
  5. 8

    manual windows to electric

    Just got a superrrr clean set of doors for my k20 they are manual windows and in my junk doors they are electric. soooo how do i swap over the elec. to the manual.?? Thanks guyss
  6. 8

    cab corner and door gap

    parden my begining bondo work. but there it is.. the gap at the top of the pic is how it should be and as it goes down it gets a little tighter. me and my buddy did the cab corner and im just seeing it now..ughh.. im pretty sure i cut out all the old bad cab. Im thinking maybe just some...
  7. 8

    cab corner and door gap

    hey guys, on the passanger side of my 86 k20 the cab corner is flush with the door i fixed my prevous problem, but the gap between the door and cab corner is close together. as you follow the gap down its fine till the cab corner area. how would i want to correct this.?
  8. 8

    What type of primer to use..

    thats my plan.. i went back to school for law enforcement and i wont have the money for a long time to give it my final paint job. soo i wana get it sprayed in black primer before the end of october
  9. 8

    What type of primer to use..

    but i see guys dp that all the time. hot rods ect.
  10. 8

    What type of primer to use..

    I'm getting ready to spray my k20 wih primer. None of my panels needed much work so no bare metal. I was suggested to use epoxy primer( in black) but also told that's just for bare metal. What are your guys sugestions and what about doin the truck in rattel can primer?
  11. 8

    prep work (for primer) question

    thank you very much. i have been useing more of a block and just the paper more than the DA. anyother tips or pics or sites people may have to help would be great...or do i just have to learn the way i learn everything eles with cars..do it my self and see what happens ?
  12. 8

    prep work (for primer) question

    Hey guys. Iv only been doin body work for a few years and im havin a bit of trouble making sure my sanding is good enough that i can shoot my epoxy primer. Im starting with my bed and i took a DA and sanded it all down to be smooth. Im doin good i think and getting it smooth and sanding down...
  13. 8

    cab corner question hellpp

    thank you.. unfortunatly it wanst spot wleded. the two of my friends (who will never help me again) installed that side and i have no idea how i didnt notice it. But how can i cut it out and save my rocker?? i really dont want to have to redo that whole side. This is making me really...
  14. 8

    cab corner question hellpp

    hey guys so on my 86 k20 i did cab corners and rockers. and the drivers side is fine but the pass. side sticks out when the door is shut. ill post a pic How would i go at repairing this??
  15. 8

    ValueTrac positraction ?????? never heard of it

    Im looking for a posi for my 2003 silverado which as a 8.5 rear diff. and i saw this valuetrac posi on rock auto for $244 and iv never heard of it.. anyone got any info?
  16. 8

    best way to replace cabfloor support?

    Hey guys im going to be replaceing the drivers side cabfloor support soon. and i wondering if someone can explain to me the best way to do this.?? the cab is on the truck, but im thinking i could jack it up and do it that way..but not sure. Thanks Liam
  17. 8

    removing fuel tank

    thank youuu!!!!
  18. 8

    removing fuel tank

    i dont drill down through the bracket right?? just through the strap
  19. 8

    Controversial Oil Filter Study

    and for the 7 years of repair experence i have. most of the people i know say the same thing. "a filter is a filter." so would wix then be the best? iv been working on cars and trucks with my uncle since iv been like 13 or 14. thats what i meant my 7 yrs...just sayin
  20. 8

    Controversial Oil Filter Study

    wow wow and wow. All through my boces program we never took a filter apart and were all told their all the same and do the same thing. for the 5 years iv been driving (i just turned 20 :) ) iv always used fram tough gaurd on my 2003 silverado and my FRESHLY REBILT 355 AHHH!!! i will neve use a...
  21. 8

    removing fuel tank

    got it out,, and both straps are broke. it looks as if the straps are rivited in the bracket. how to i install new ones and remove old from bracket??>
  22. 8

    Fuel tank saddle brackets. where to find..

    I was removing my fuel tank on my 86 k20 and all the bolts broke on the saddle bracket that bolt to the frame. I cant seem to find them anywhere!!!! does anyone know a place of a website or happen to have a pair i could buy? Thanks
  23. 8

    removing fuel tank

    on my 86 k20 how do i drop the tank? i got the straps off but it looks like those tank braces that are bolted to the frame have to come off.?? thansk
  24. 8

    missing frame crossmember?

    Hey guys on my 86 K20 im missing a strength crossmember that must of rotted away hah. its the crossmember that should be in above the rear diff, or somewhere around there. What would be the best way to make one?? just square stock? or what
  25. 8

    exhuast leaks

    I just installed my header back kit from summit and I got some leaks at the pipes that slide over the collecter. The guy who expanded them made them a weeee to big. He clamps are as tight as I can get them. What should my fix be. Weld the leaks? Or putty?

Latest posts

Forum statistics

Threads
45,566
Posts
986,352
Members
38,653
Latest member
82SquareBurb
Top