Search results

  1. Ontheboulder

    winter project success!

    after a winters worth or chasing wiring gremlins,bad grounds,shorted wires,and a bad turn signal switch, I finall got everything working!! just put in the new printed circuit,gave it a test and it all works!! Had to rotate a couple of the new LED dash lights but got it done. fired it up to check...
  2. Ontheboulder

    Has anyone superglued the copper contacts down on the circuit board ?

    success!!!! got the circuit board and gauges back in the truck, everything works!! I can finally put this part of the project to bed!!
  3. Ontheboulder

    Has anyone superglued the copper contacts down on the circuit board ?

    just on the circuit board, nothing on the bulb holders, I bent the little copper tangs on the holders up a bit so they would have more pressure against the circuit board, the new bulb holders seemed to fit a little snugger when in place
  4. Ontheboulder

    Has anyone superglued the copper contacts down on the circuit board ?

    Just replaced my printed circuit today,everything laid down pretty nice, sanded all the electrical connections for the gauges and lights and used new bulb holders. I used just a dab of super glue on the corners and near the turn indicators to keep them in place
  5. Ontheboulder

    What have you done to your square lately??

    I bought a headlight relay harness for the 87, didn;t like the cheesy pigtails that were on the harness so I am soldering new pigtails on the harness for the headlights. should be a much better set up.
  6. Ontheboulder

    fedex smart post

    Not sure if anyone else has had this problem, but FEDEX smartpost is anything but smart!! I ordered some stuff from LMC awhile back and they shipped it FEDEX smartpost. it took nearly 3 weeks to get here after FEDEX sent it on a cross country tour. Ordered again form LMC had them ship USPS, came...
  7. Ontheboulder

    Installation information for Radiator #CU730

    I put an aluminum radiator in my 87 gmc, It took a bit of modification to get it to fit, even though they said direct replacement!!
  8. Ontheboulder

    emergency brake cables

    I am using the LMC catalog page as a guide for the parts needed then just gonna try to make it work! My Jeep J20 has the same type of Ebrake cable system under it so I am checking that as well
  9. Ontheboulder

    Flip up wipers arms?

    these are for a Jeep,and a ford, neither had wet arm stuff,both were hook ends, I went on the dorman website and searched windshield wiper arms. at 18 inches they might work. I would have to switch to cowl squirters but not a big deal for me
  10. Ontheboulder

    emergency brake cables

    thought about that but I think the drums and hubs maybe different, and in short supply around here!! I think this retro fit to an earlier type of cable system should work, just may have to get a different cable coming off the pedal if it doesn't hold up
  11. Ontheboulder

    emergency brake cables

    thats exactly how I have mine routed now, just need to figure out the connection from the cab cable to the u cable going back to the rear end, need a couple more hangers and I think this will work, I bought a cable connector from Lokar to make that connection after I cut the cable down that goes...
  12. Ontheboulder

    emergency brake cables

    the 87 had push in style Ebrake cables thru the backing plate, this has the bolt on style
  13. Ontheboulder

    Flip up wipers arms?

    dorman # 42591 and 42630 are what I found, both are 18 inches long I looked at the pics and both are spline push on type, but no mention of the spline diameter. My GMC has .61 size spline.
  14. Ontheboulder

    What have you done to your square lately??

    thanks , the area around the turn indicators seem to be a weak spot as well,I was thinking using some silicone to hold it down would help the plastic board get trained to the curves. I have had this cluster in and out 4 times chasing gremlins this winter so I will definitly check all the lights...
  15. Ontheboulder

    What have you done to your square lately??

    doing that to my gmc ,waiting on LMC for a new printed circuit. How was yours from LMC,also got some new bulb holders as mine seem to be loose in a few holes. Did you glue or silicone your new board down to keep it in place?? thinking I willl do that to mine when I get it
  16. Ontheboulder

    the car and truckshop.com

    got a new catalog in the mail yesterday,not sure if anyone else has used them. seem to be a good selection and decent prices. Truckandcarshop.com
  17. Ontheboulder

    Tail light modification

    All I did was take out the plastic fin in the bucket. If anything it puts out more light!
  18. Ontheboulder

    Different square

    Been a helluva rig! Only 83k on the odometer! Purrs like a kitten
  19. Ontheboulder

    Different square

    Jeep J20
  20. Ontheboulder

    Tail light modification

    Here is the taillight on
  21. Ontheboulder

    Tail light modification

    Here is a cou pictures of the taillight bucket after I cut it out
  22. Ontheboulder

    Tail light modification

    exactly, I cut the marked out area away, no exposure to the backside of the bulb holder. so no weather concerns. lots more light out of the side of the lens. I think the LED bulbs will make it even better, I will get a picture soon
  23. Ontheboulder

    emergency brake cables

    Has anyone ran into the problem of using and older style 14 bolt in a newer truck? My 87 has an earlier rear end under it and the Ebrake cables are different. GM went to routing the Ebrake cables down the drivers side in later years. they ran the passenger side cable over to the drivers side to...
  24. Ontheboulder

    Edelbrock 1405 carb running rich

    good place to start on tuning your carb is about 1-1/2 turns out,timing will make a big difference as well.
  25. Ontheboulder

    Has anyone superglued the copper contacts down on the circuit board ?

    I would use some clear silicone my self, I know those boards seem to be moving a bit and a new one would probably need to tied down for a bit until the plastic gets its curves and bumps worked out, especially around the turn indicator bulbs

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,338
Latest member
jw23655
Top