Search results

  1. E

    Pondering Oil Types [and bad government influence on OEM choices]

    I watched a couple videos of that guy's. Had to fast forward a bit. He blabbers on and takes forever to get to the point. It is good info but he needs to study editing. Get to the point!!
  2. E

    Smog removed: how to cap manifolds?

    Get a 3/4" pipe cap or remove the tubes from the manifolds and order some brass 1/4" plugs to fill the holes.
  3. E

    Blower Motor Stopped Turning

    I would just pull the rubber boot back and leave the motor connected. Turn it on high and measure voltage. This way you are checking it loaded. If there is a voltage drop it will show with this one test.
  4. E

    Replacing a single frame rail, can it be done?

    Interesting that they go that deep for a VIN check. How do they find the frame vin when there is rust? Do they do this if you have a title and it was registered previously in Kansas? In my state VIN verifications are done when registering a car from out of state, regardless of the vehicle age...
  5. E

    Replacing a single frame rail, can it be done?

    Here in CT they do VIN verifications. They look at title or registration and compare to windshield VIN and door VIN. I have been in the car business here for 40 years. Sold many vehicles through my own dealership. Paid for many VIN verifications. Never once did the inspector look anywhere but...
  6. E

    Glass lock strip replacement

    I have had hit or miss luck with LMC. I bought fuel tank insulation for the straps on fuel tanks. What a joke. They sent roofing felt. I ended up buying 1/16" thick x 2" rubber and tossed the roofing felt scraps.
  7. E

    Aftermarket A/C?

    They make 12 volt roof mounted unit. They sell them for use on heavy equipment. I would bet you need a pretty stout alternator to run it.
  8. E

    Ball joint

    Be careful heating a ball joint. When the grease expands it causes pressure. I watched a moron blow a hole in his foot touching a ball joint out of a Ford truck in the 80s. The knuckle was removed and the stud shot out like a bullet. He was out of work for a couple weeks. I told him not to do it...
  9. E

    Proportioning Valve and Bleeding

    If the hoses are more than 5-6 years old you should replace them as a matter of maintenance. Brake fluid should be flushed every two years regardless of mileage. Brake fluid absorbs water and that water not only corrodes the brake parts it lowers the boiling point of the fluid significantly. If...
  10. E

    Intake manifold and stripped bolt

    Subjective, yes. As I said, do what you feel comfortable with. We have given OP some options.
  11. E

    Intake manifold and stripped bolt

    Teflon pipe dope stays pliable as does #2 Permatex. @Ricko1966 has maybe a simpler solution but I would not want two different size intake bolts. I like doing things correctly. You decide what you are comfortable with and what is doable. I like McMaster-Carr for taps and high quality hardware.
  12. E

    Truck Overheating

    195 deg thermostat is fine. Going with a lower temp. to fix a problem is a band-aid. You need to diagnose the underlying condition. As someone asked. Did this problem appear only after thermostat replacement or did you replace it try to fix it? You could have an air pocket and that will give...
  13. E

    Intake manifold and stripped bolt

    I would use a Helicoil. They are a permanent repair. Put a dab of Red Loctite on the insert on the outside so it locks to the head. Then let it dry and fit you intake bolt. Torque to spec. With Loctite one drop it sufficient. You do not need it dripping. Also if that bolt goes into a coolant...
  14. E

    Replacing K20 fuel tank

    I did not have an inner tube available to cut up. Bike tube would work well as it is thin. A car or truck tube would make getting the straps started tougher. One of mine was a real pain in the butt. I had to use a ratchet strap and really crank on it to get the nut started. I tightened it down...
  15. E

    Replacing K20 fuel tank

    I want to say the aftermarket switching valves require rewiring. Whatever you do don't waste your money on the LMC Truck "fuel tank anti-squeak" kit. It is just scraps of roofing felt. What a rip off and a poor choice of material. I threw the two I bought in the garbage. I found some 2" wide x...
  16. E

    A/C Compressor

    If your compressors are failing because they are disintegrating. You need to get all that debris out of the system or it will destroy your new compressor. Simplest way is to replace everything but it is the most expensive and time consuming. There are flush products that can be used. Pro shops...
  17. E

    Need help with part number/name 1987 V3500 7.4L N TBI

    Thanks! I have a part catalog for my truck but I missed the auxilary fan picture. That switch listed there is exactly what I took out. I found a different one in a different section. Appreciate it!
  18. E

    Need help with part number/name 1987 V3500 7.4L N TBI

    Yes but I found the sender.
  19. E

    I think a rod spun a bearing in my rebuilt 454

    I think you need to pay someone else to straighten this thing out. I would give the current shop a chance to do the right thing and refund your money. If they don't take them to small claims court. You will have a very good chance of winning.
  20. E

    Dual tank install

    The fill hoses are available, at least they are for my 1987. I just received my order. New filler necks and hoses. The original valves are wired different than the current replacements. At least I am told that. I found an NOS one for my truck.
  21. E

    1974 NOS doors.

    I don't like aftermarket sheet metal. It is never the same despite the claims. Since I am paying someone to do the body work. The NOS door made sense because I did not have to pay the extra couple hours labor to clean, blast and prep the used door.
  22. E

    1974 NOS doors.

    I bought an NOS door for my 1987 V3500 restoration project. I paid $1000 for it. In hind sight I should have bought a clean used door.
  23. E

    1981-87 Chrome body side molding

    As requested. Left 14027593 Right 14027594 Retainer (2) 14018564 Retainer (2) 14022856 Spacer (2) 15606343
  24. E

    Any tricks to getting your SB doors to close easier?

    What color PEX works best? :anitoof:
  25. E

    1981-87 Chrome body side molding

    I am restoring my V3500 and it had the black trim. One bed corner was missing. I found two NOS ones on eBay. If you need the part numbers let me know. The black trim, last I checked, was available on a roll.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,339
Latest member
wonone
Top