Recent content by Ethan0

  1. E

    Need help with clutch fork alignment

    I’m putting a new clutch/flywheel in right now and getting to put the clutch fork and bearing in but the bearing/fork doesn’t line up correctly in line with everything else. When the fork is positioned with the pivot ball in the divot in the fork it’s about 1/2”-3/4” off the center line. If I...
  2. E

    Vibration at 2500 rpm

    Motor mounts were shot but I replaced them a few months ago. Didn’t make much of a difference in the vibration. The dampener doesn’t look like it’s moving around while revving the engine but I’m not certain it’s not a problem.
  3. E

    Vibration at 2500 rpm

    I know it’s been awhile since posting this thread but I’m getting back to finding this vibration/shake. After checking and replacing a few things nothing fixed it so I left it alone. Now thinking that the problem with the clutch/flywheel not being centered or loose I pulled the trans out and...
  4. E

    Which headers to buy?

    Okay, I was assuming the engines or exhaust ports wouldn’t be different but just wanted to be sure. Thanks for the help!
  5. E

    Which headers to buy?

    Wanting to buy some headers for my truck. It’s a 76 k10 but the thing is the engine is an 83 350 and I’m not sure if I should buy the headers that will fit the truck, the 76, or the the engine, the 83 350. Not sure if there are any differences between the 76 350 and 83 350 engines. So should I...
  6. E

    Vibration at 2500 rpm

    Looking for some help at figuring out a vibration/shake at around 2500 rpm. There is a small shake at idle but it smooths once I start giving it gas. Then at about 2500 rpm it feels like the whole truck starts shaking/vibrating pretty badly. It does it in neutral with the clutch in or out, while...
  7. E

    Muffler recommendations

    Ok, I was thinking about flowmaster 40 or super 44 at first but heard people say that they sound tinny sometimes but I’ve also heard a lot of good so I might just go with one of those
  8. E

    Muffler recommendations

    Not looking for anything too expensive, probably under $200 or so. It’s single exhaust setup that goes out to the rear bumper. Muffler sits at the end of the cab. Just looking to change the muffler from factory. Was looking at at flowmasters or magnaflows but wasn’t sure if there were better...
  9. E

    Muffler recommendations

    I’m looking for muffler recommendations for my 1976 k10. Has a stock 350, stock manifolds, and a cat. Old one needs to be replaced. Looking for one that makes it a little louder than stock and gives it more of a deep rumble. Has 2 1/4” pipes. Any recommendations would be great. Thanks.
  10. E

    Need help with SM465

    That’s what I’m thinking. For now I just hooked up some springs to keep it in place.
  11. E

    Need help with SM465

    Okay, the truck will move now. I accidentally kicked the transfer case into neutral, my bad lol. But I think the clutch fork slips off of the pivot ball after I push the clutch pedal in about 2-3 times.
  12. E

    Need help with SM465

    Also, the clutch fork has a lot of play. I’m able to move it around a lot up and down and left to right. Not sure if it being this loose is a problem.
  13. E

    Need help with SM465

    Ok thank you a lot for help
  14. E

    Need help with SM465

    That’s funny. That could be a possibility. I’m checking the clutch linkage and clutch fork and bearing now. Would it not be engaging because the clutch is not adjusted correctly?
  15. E

    Need help with SM465

    I recently swapped my 454 for a 350 and now the truck won’t move. I can’t get the clutch to engage or disengage. I can put the clutch pedal in and out and the transmission goes into gear but when I take my foot off the clutch it doesn’t move. Don’t know what the problem could be at this point...
See more

Latest posts

Forum statistics

Threads
45,570
Posts
986,477
Members
38,660
Latest member
Dennis Blom
Top