front end alignment

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

BurbanPena

Member
Joined
Jan 20, 2022
Posts
44
Reaction score
51
Location
Idaho
First Name
Brian
Truck Year
1989
Truck Model
V1500
Engine Size
350
I just replaced my front end on my 89 v1500 has any one done a at home alignment?

what's your technique on completing this, my alignment shop is ways away and I cant get in until next week and I need my truck between now and then.
 

Originalthor

Full Access Member
Joined
Aug 22, 2021
Posts
1,084
Reaction score
3,659
Location
Saskatoon Saskatchewan
First Name
Scott
Truck Year
1989
Truck Model
Suburban
Engine Size
5.7
I take a piece tape and put it on the center of the tire and make a mark in the center of the tape. Then measure front then rotate tire to back and measure again. When rotation of tire back and forth also measure the distance up so your level. Toe in a quarter inch.
 

BurbanPena

Member
Joined
Jan 20, 2022
Posts
44
Reaction score
51
Location
Idaho
First Name
Brian
Truck Year
1989
Truck Model
V1500
Engine Size
350
ho
I take a piece tape and put it on the center of the tire and make a mark in the center of the tape. Then measure front then rotate tire to back and measure again. When rotation of tire back and forth also measure the distance up so your level. Toe in a quarter inch.
are you basically splitting the difference from front to back? or do need to end up with the same measurement front to back and then toe in a 1/4 inch

example:60 in the back 59 3/4 in the front ?
 

Originalthor

Full Access Member
Joined
Aug 22, 2021
Posts
1,084
Reaction score
3,659
Location
Saskatoon Saskatchewan
First Name
Scott
Truck Year
1989
Truck Model
Suburban
Engine Size
5.7
ho

are you basically splitting the difference from front to back? or do need to end up with the same measurement front to back and then toe in a 1/4 inch

example:60 in the back 59 3/4 in the front ?
Thats correct.
 

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
1,982
Reaction score
2,835
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
Easier way is what used to be called an oil can alignment.
Use some sort of blocks set them against the tire on both sides. Then with 2 straight edges, long extensions, pieces of steel what have you, lay those on top of the blocks against the sidewall. Then with 2 tape measures lay them on the top of the straight edges. The difference front to back is toe in or out. You will need a helper to hold the other end.
 

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
6,877
Reaction score
12,019
Location
Auburn, Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
A 1/4 toe in is way too much. Ideally you want a 1/16, maybe an 1/8.

Toe is a tire wearing angle so you need it to be right if you're not going for an alignment for a while.
I agree. In fact I’d start at dead zero and if it wanders too much then crank it in ever so slightly.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,304
Reaction score
8,441
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
I do my own all the time I'll put up pics and give some general directions in a minute.I now use longer angle the longer the more accurate,you should be able to find alignment specs on line,and conversion charts degrees to inches I always can. The pictures are for toe,which you set last,I have a caster gauge you don't,so we're going to skip that and cross our fingers. You're going to want to check camber first,park the truck somewhere level use plywood squares and or linoleum floor tiles under the tires to make the truck level. Then to be real accurate tape a piece of string and a plumb bob inside the hood opening let it dangle over the fender by the wheel hub put a sponge between the fender and the string as a shim. Measure from the string to the wheel at the top and bottom there's your camber measurement. Less accurate but easier push a level up against the wheel now pull the top or bottom of the level out eyeball the gap there's your camber.
 

Attachments

  • 20170223_103300.jpg
    20170223_103300.jpg
    270.6 KB · Views: 102
  • 20170223_101917.jpg
    20170223_101917.jpg
    287.1 KB · Views: 97
  • 20170223_101731.jpg
    20170223_101731.jpg
    325.9 KB · Views: 102
Last edited:

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,304
Reaction score
8,441
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
I cam get you more accurate than that,if I teach you how to build a string box, but this is really good enough. If you have to add or remove shims or twist eccentrics for camber do them equally meaning a 16th at the front of the a arm and 16th at the back also. To level your alignment area pull your truck up where you are going to align it put a brick in front of each front wheel use string level or a straight edge an level from brick to brick,that will tell you which side needs shimmed for level and how much,put your shims down throw some sand on them and bring the truck forward.And this all doesn't have to perfect just reasonable close, you never drive down perfectly level roads.The sand is to minimize turning resistance as your setting toe.
 
Last edited:

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,304
Reaction score
8,441
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Alignment degrees to inches calculator rob Robinette. Type 89 chevy suburban alignment specs they have them at gmt400. I now use 3 ft angle, it's held up by the bungees,same height front and a back of the tire same height on each side about 6 inches up you don't want the tire bulge at the bottom affecting your measurement
 
Last edited:

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,304
Reaction score
8,441
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Way better than I can teach you to build a string box.I just started reading his set up he doesn't explain that the holes in the conduit have to be the same on each stick,that's what holds the strings parallel then make sure you have the string to the middle of the hub at the same measurement on each side so if left front is 4 inches to the hub right front has to be 4 inches left rear is 3 right rear is 3 so the string is parallel to its self and to the car.
http://speed.academy/diy-wheel-alignment-how-to-guide-explained/2/
 
Last edited:

idahovette

Full Access Member
Joined
Aug 7, 2016
Posts
7,176
Reaction score
15,608
Location
Weiser Idaho
First Name
Perry
Truck Year
1975-1979
Truck Model
K20-K10
Engine Size
350
This is how I do mine. I still have my Hunter machine I used when I had my shop downtown....old but works.....and my old balancer
You must be registered for see images attach
You must be registered for see images attach
 

GTX63

Full Access Member
Joined
Nov 27, 2022
Posts
916
Reaction score
3,726
Location
Tennessee
First Name
Ty
Truck Year
1985
Truck Model
K10
Engine Size
350
Once you have toe set, you can straighten your steering wheel by turning both tie rod sleeves in equal amounts, in the same direction.
 

GTX63

Full Access Member
Joined
Nov 27, 2022
Posts
916
Reaction score
3,726
Location
Tennessee
First Name
Ty
Truck Year
1985
Truck Model
K10
Engine Size
350
xc_hide_links_from_guests_guests_error_hide_media
 

Scott91370

Full Access Member
Joined
Apr 2, 2018
Posts
985
Reaction score
1,005
Location
Burleson, Tx
First Name
Scott
Truck Year
1985
Truck Model
Sierra1500
Engine Size
350
We need to know what 'rebuilt the front means'.
Is it just outter tie rod ends? Was it ball joints? Replace springs? Everything?
If it is only outter ends then toe should be the only thing that changed. Post #8 is perfect.
If ball joints or springs then yeah, caster & camber will have changed too.
 
Last edited:

Forum statistics

Threads
43,936
Posts
946,049
Members
35,982
Latest member
jake26104
Top