Limited slip in the front?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

emsherer

Junior Member
Joined
Jan 25, 2013
Posts
6
Reaction score
2
Location
TN.
First Name
E.M.
Truck Year
85
Truck Model
1500
Engine Size
350
I have an 85 K-10 4x4, basically a good old work truck. I want to install a limited slip diff in the rear Just to improve winter drivability in the snow. What are your thoughts about a limited slip in the front also to make this truck almost unstoppable in snow. I live way up in the mountains and need to be able to go in winter. Thanks
 

mtnmankev

Full Access Member
Joined
Jun 10, 2014
Posts
1,621
Reaction score
3,280
Location
Ash Fork, Arizona
First Name
Kevin
Truck Year
1984, 1983
Truck Model
K10, C20
Engine Size
383 Stroker, 350
I get both snow and horrible mud being off the grid, and I put limited slip in the front (so far) and it makes a HUGE difference.
It's best in the front if you have part time 4x4.
Someday I may put it in the rear.
 

Danderson

Full Access Member
Joined
Feb 23, 2020
Posts
59
Reaction score
192
Location
Chatsworth GA
First Name
Doug
Truck Year
1977
Truck Model
K10
Engine Size
350
I put an Eaton Detroit Truetrack in the front of my 1977 K10 and I've been very happy with the results. I have a cabin on top of a mountain and to get to it I have to drive about a mile of gravel/dirt road that gets very slippery when it rains or snows. Before I made the change the truck used to struggle a bit, but now it climbs like a mountain goat. It made a really big difference.

I looked at most of the available limited slip units before I settled on the Truetrac. It is a bit more expensive, but there are no clutch disks to wear out and no special fluid or additives are needed like with the clutch units.
 

Craig Nedrow

NADAR UNDER THE RADAR
Supporting Member
Joined
Sep 1, 2018
Posts
823
Reaction score
1,459
Location
Washington State
First Name
Craig
Truck Year
1973 (have two), 1985
Truck Model
K10, K20, C20
Engine Size
350, 454, 6.2 Detroit
I installed this in my 14 bolt FF with an open diff. Been running it for a couple months, and very pleased. My front is a Dana 44, and Yukon does not make diff unit like this, and BTW no clutches to rebuild. Since Grizzly does not make a lunchbox locker, I will use the US gear Spartin locker.
gG here: http://www.usastandardgear.com/diff...125&DiffName=Dana+44+Front,+Standard+Rotation

You must be registered for see images attach
 

trukman1

Full Access Member
Joined
Apr 20, 2018
Posts
337
Reaction score
134
Location
USA
First Name
Gary
Truck Year
1988
Truck Model
K5 Blazer
Engine Size
5.7 L (350)
I installed this in my 14 bolt FF with an open diff. Been running it for a couple months, and very pleased. My front is a Dana 44, and Yukon does not make diff unit like this, and BTW no clutches to rebuild. Since Grizzly does not make a lunchbox locker, I will use the US gear Spartin locker.
gG here: http://www.usastandardgear.com/diffdetails.aspx?DiffID=125&PartsLink=PartCats.aspx?SearchMode=Diff&TypeID=3&Type=Dana&DiffID=125&DiffName=Dana+44+Front,+Standard+Rotation

You must be registered for see images attach

That resembles my Detroit Locker. Great for locking both wheels together but can get a bit tricky in the winter as the rear won't have enough friction on slippery roads to unlock causing some interesting driving characteristics, to say the least.
 

cptsnoopy

Junior Member
Joined
Apr 13, 2020
Posts
5
Reaction score
1
Location
Phoenix, AZ
First Name
Charles
Truck Year
1981
Truck Model
K-20 Silverado
Engine Size
454
I installed a limited slip in the front of my 81 K20 and have only tried it once in the snow on a highway near Mt Hood. It was scary to drive over about 30mph. I unlocked the hubs and put the truck back into 2hi. Was able to drive without it trying jerk the front left or right after that. If the conditions had been worse, I think it would have been an advantage over no limited slip as I would have been traveling much slower.
 

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,121
Reaction score
6,038
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Are you supposed to exceed 30 or so mph in 4wd on a road, though? I just know it typically is very clear about short distances, not high speeds, not while turning(esp at speed) and not on pavement unless straight line? newer CV, complex systems, etc make that doable but these are cast iron and all direct processes
 

77 K20

Full Access Member
Joined
Nov 9, 2012
Posts
3,075
Reaction score
3,044
Location
Montana
First Name
Mike
Truck Year
1977
Truck Model
K20 5" lift
Engine Size
HT383 fuel injected
I have the Eaton truetrac in the front and a detroit locker in the rear. When in 4wd it is awesome in the snow. I can still turn sharp without the front end pushing like if it was fully locked.

When the highway is fully snow covered I've driven in 4wd at 45-55 mph for 2 hours or so. Everything was fine. The truck used to be a full time 4, so no reason it can't still go at highway speeds (when the road surface is slippery- snow, gravel).

Why not on dry pavement? With a part time kit 4wd locks the front and rear driveshafts together. When it was full time then the front and rear driveshafts can spin at different rates for going around corners.
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,024
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
Adding a limited slip to the front will make a huge difference without a doubt.

As for driving fast in the snow, just because you have traction to drive fast doesn't mean you have traction to stop. Drive according to the conditions you are in. Just a simple fact, I can't count the number of people the have 4WDs and haul a$$ down the freeway passing everyone else doing 40 because of the conditions, then a couple miles down the road they are in the median flip on the lid. Common sense is a real rare quality in this day and age.
 

77 K20

Full Access Member
Joined
Nov 9, 2012
Posts
3,075
Reaction score
3,044
Location
Montana
First Name
Mike
Truck Year
1977
Truck Model
K20 5" lift
Engine Size
HT383 fuel injected
That was why I only said 45-55. All the rest of the idiots are still doing 70. :D
Any slower and I'd get run over.

Driven for over 30 years in the snow. The only slide off I had was my first winter. No damage, but by dad's blazer was stuck bad. :rolleyes:
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,024
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
@77 K20 wasn't point at you just pointing out about the ones that haul a$$.
 

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,121
Reaction score
6,038
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
I have the Eaton truetrac in the front and a detroit locker in the rear. When in 4wd it is awesome in the snow. I can still turn sharp without the front end pushing like if it was fully locked.

When the highway is fully snow covered I've driven in 4wd at 45-55 mph for 2 hours or so. Everything was fine. The truck used to be a full time 4, so no reason it can't still go at highway speeds (when the road surface is slippery- snow, gravel).

Why not on dry pavement? With a part time kit 4wd locks the front and rear driveshafts together. When it was full time then the front and rear driveshafts can spin at different rates for going around corners.

I'm talking about a part time case, full time was designed to allow that. I'm just going on general knowledge, dry pavement I said because inevitably you're going to turn or not go perfectly straight and each tire being very well planted puts strain esp in turn
 

Forum statistics

Threads
41,850
Posts
903,456
Members
33,362
Latest member
Dhatch84
Top