Like to put a stock tach in my 88 Blazer ?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

JTWard

Full Access Member
Joined
Mar 3, 2017
Posts
78
Reaction score
73
Location
SE Pennsylvania
First Name
James
Truck Year
1990
Truck Model
C1500 Silverado
Engine Size
350 Gasoline
What do I need to do this job ? I bought a good instrument cluster off ebay with a tach, and I already have a good housing, so I bought a printed circuit for a Blazer with a Tach, and dam% sure their different. One is 2 leads short of all 18, it's only got a gas gauge and the 18 leads go I think to the tach which would of been in the gas gauge space on the cluster. What do you think ?
You must be registered for see images attach
You must be registered for see images attach


You must be registered for see images attach
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,495
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
What year cluster did you buy? You need a '78 or newer cluster to swap in. The tach harness is separate from the printed circuit.
 

JTWard

Full Access Member
Joined
Mar 3, 2017
Posts
78
Reaction score
73
Location
SE Pennsylvania
First Name
James
Truck Year
1990
Truck Model
C1500 Silverado
Engine Size
350 Gasoline
It was listed as 1979 to 1990. I have a new oil pressure gauge and the overall Lt. Blue gauge cluster housing is in very good condition. Yet it has an odd gauge in it. I'm not going to use it, but I've never seen one and I'm wondering what it is. But what I need to know is what do I need for this conversion. Thank you !
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,495
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
So I'm guessing you have a cluster from a medium duty truck then? Is your fuel gauge built into the tachometer?

If its a cluster from a C50-70 truck, all bets are off as far as wiring pinouts go. You will just have to trace the contacts on your stock cluster and your new cluster, then compare and see what pins need moved around in the connector or what wires need added in.
 

roundhouse

Full Access Member
Joined
Apr 5, 2014
Posts
669
Reaction score
527
Location
atlanta ga
First Name
justin
Truck Year
77,78,79,80 ?
Truck Model
K10
Engine Size
350
Some had vacuuum gauges and some had a air pressure gauge for the brakes

The printed circuit changed a lot over the years

You just have to follow the circuit and see where it goes

You can make a tool to pull the wires out of the main plug and move them
 

JTWard

Full Access Member
Joined
Mar 3, 2017
Posts
78
Reaction score
73
Location
SE Pennsylvania
First Name
James
Truck Year
1990
Truck Model
C1500 Silverado
Engine Size
350 Gasoline
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
What year cluster did you buy? You need a '78 or newer cluster to swap in. The tach harness is separate from the printed circuit.
It's a 1986, and I think it was a diesel. I don't know what the bottom left gauge is and upon looking at the LCM catalog, I found I needed a replacement base/cluster holder and I bought 6 more of the clips that snap on holder and the gauges snap into the holder and make contact with the grid. I have another question, would you replace the dash lights with LED's
You must be registered for see images attach
 
Last edited:

1987 GMC Jimmy

Automobile Hoarder
Joined
Jan 23, 2016
Posts
5,848
Reaction score
2,387
Location
Mississippi
First Name
Jesse
Truck Year
1987
Truck Model
V1500 Jimmy
Engine Size
350
I’ll chime in. I use the Silverstar incandescent bulbs in my clusters. They do a good job, and there’s a considerable improvement in the backlit square body cluster where I didn’t see as much in a postlit cluster (my Caprice). Here’s a pic from the night I did them.

You must be registered for see images attach
 

JTWard

Full Access Member
Joined
Mar 3, 2017
Posts
78
Reaction score
73
Location
SE Pennsylvania
First Name
James
Truck Year
1990
Truck Model
C1500 Silverado
Engine Size
350 Gasoline
So let me have it, the dash cluster and tach are no good for my 88 Silverado K5 Blazer 350 V8 ?
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,495
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
So let me have it, the dash cluster and tach are no good for my 88 Silverado K5 Blazer 350 V8 ?

You can make those work, you just have have to trace where all the contacts end up in the harness connector compared to your stock cluster, then re-pin wires if it's needed to match it up.

The printed circuit you bought will not work however. It is for the light duty trucks with a fuel gauge in the lower left and no gauge built into the tach.

You have a medium duty truck cluster with a fuel gauge in the tach, and an air pressure gauge in the lower left corner.
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,495
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
I also just noticed that your new cluster has an ammeter gauge instead of volts. If not rewired correctly, it can cause a fire.

Personally, I'd modify the stock cluster to use that nice tach/fuel combo gauge. Chances are good that it was an 8 cylinder too, rather than a 4 or 6 cyl diesel. So as long as it still works, it shouldn't need calibrated.
 

JTWard

Full Access Member
Joined
Mar 3, 2017
Posts
78
Reaction score
73
Location
SE Pennsylvania
First Name
James
Truck Year
1990
Truck Model
C1500 Silverado
Engine Size
350 Gasoline
So I'm guessing you have a cluster from a medium duty truck then? Is your fuel gauge built into the tachometer?

If its a cluster from a C50-70 truck, all bets are off as far as wiring pinouts go. You will just have to trace the contacts on your stock cluster and your new cluster, then compare and see what pins need moved around in the connector or what wires need added in.

You must be registered for see images attach
Yeah, it's got a
You must be registered for see images attach
4000 RPM tach and the gas gauge is in the tach on the bottom. The more I investigate it I starting to think this isn't going do-able. Maybe a 'A' pillar tach ?
 
Last edited:

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,495
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
There's a company that makes a drop-in tach that looks factory. It has the fuel gauge in it too. All you have to do it run a tach harness which is very easy.

I just can't remember the name of the company. But there's been threads about it here in the past.
 

Craig 85

Full Access Member
Joined
Jan 25, 2017
Posts
3,889
Reaction score
4,024
Location
Nashville, TN
First Name
Craig
Truck Year
1985
Truck Model
K30 SRW
Engine Size
454/TH-400/NP205
There's a company that makes a drop-in tach that looks factory. It has the fuel gauge in it too. All you have to do it run a tach harness which is very easy.

I just can't remember the name of the company. But there's been threads about it here in the past.

It was GM Sports. Frankenchevy just called them about 2-3 weeks ago. They told him the man making the tach died and they don't know what their future plans are. The website says on backorder until further notice.
http://www.gmsports.com/trucks

On my last truck I mounted the tach on the column Autogage 3 3/4" #2300. When I pulled it into gear, it would center in the dash. On my '85 I'm doing the same thing, but I'm using a 2 3/4" Autogage #2306. I also put a green filter on the bulb.

You must be registered for see images attach
 

dvdswan

Full Access Member
Joined
Mar 11, 2014
Posts
2,366
Reaction score
2,024
Location
Port Orchard, WA
First Name
Dave
Truck Year
1978
Truck Model
K10
Engine Size
350
So what do you plan on doing with the cluster?
 

roundhouse

Full Access Member
Joined
Apr 5, 2014
Posts
669
Reaction score
527
Location
atlanta ga
First Name
justin
Truck Year
77,78,79,80 ?
Truck Model
K10
Engine Size
350
I would just cut out your existing cluster to fit the tach

And re pin the wires or make some that go to the fuel gauge

That tach is from a diesel if it’s a 4000
That were usually driven from the alternator ?
 

Forum statistics

Threads
41,860
Posts
903,690
Members
33,372
Latest member
83elcowes
Top