Steering problems need some help

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

tjd50317

Junior Member
Joined
Nov 6, 2012
Posts
12
Reaction score
0
Location
des moines
First Name
tom
Truck Year
1983
Truck Model
k2500
Engine Size
350
I have an 83 k2500 that the steering seems to bind or lock up. When driving down the road it will pull a little the left and bind and then release pulling the ftruck to the right. New pump, box, stabillizer, wheel bearings and shocks. It has been at he garage and they are puzzled. They have check out the front end and cant find anything wrong. Any ideas? I need help. I am new to the forum and really need to get fixed. Thanks Tom
 

8T6K5

Full Access Member
Joined
Jun 22, 2012
Posts
1,128
Reaction score
112
Location
AZ
First Name
Jerry
Truck Year
1986
Truck Model
K5
Engine Size
L98 350 TPI
New pump, box, stabillizer, wheel bearings and shocks. It has been at he garage and they are puzzled. They have check out the front end and cant find anything wrong. Any ideas?

No mechanic here, but it seems to me that if everything from box down has been replaced or checks out, go up from there..... rag joints, steering shaft column?
 

tjd50317

Junior Member
Joined
Nov 6, 2012
Posts
12
Reaction score
0
Location
des moines
First Name
tom
Truck Year
1983
Truck Model
k2500
Engine Size
350
2" lift 285 tires. problem did not start until pump went out in spring, replaced and had problem off and on since took pump back and replaced. still had problem so i took to garage. Thought about column and shaft but hate to just start replacing parts but might not have much choice. Thanks Tom
 

tjd50317

Junior Member
Joined
Nov 6, 2012
Posts
12
Reaction score
0
Location
des moines
First Name
tom
Truck Year
1983
Truck Model
k2500
Engine Size
350
Just went through a 84 cj7 repalced everything from steering column to lock outs. Thought this a much bigger job did not want to spend the money on heavier tools to do the job but if the garage is just going to replace parts until it is fixed I might as well do that.
 

8T6K5

Full Access Member
Joined
Jun 22, 2012
Posts
1,128
Reaction score
112
Location
AZ
First Name
Jerry
Truck Year
1986
Truck Model
K5
Engine Size
L98 350 TPI
Belt on pump good? Slipping at all?
 

tjd50317

Junior Member
Joined
Nov 6, 2012
Posts
12
Reaction score
0
Location
des moines
First Name
tom
Truck Year
1983
Truck Model
k2500
Engine Size
350
tightened when i put pump on 2 weeks ago will look at again tomorrow.
 

89Suburban

Supporting Member
Supporting Member
Joined
Dec 7, 2010
Posts
24,590
Reaction score
6,023
Location
Southeast PA
First Name
Paw Paw
Truck Year
2007
Truck Model
Chevrolet Tahoe LT
Engine Size
5.3, 4WD
I been hearing horror stories here from a few members of new steering pumps being installed and being bad right out of the box, something to keep in mind.
 

Zaar

Full Access Member
Joined
Oct 4, 2012
Posts
64
Reaction score
6
Location
Delaware
First Name
Zaar
Truck Year
1985
Truck Model
k20/30
Engine Size
355.
could be a bad steering box but also check that your front calipers arent jamming or binding up on you had the same issue and had a hose collapse and the caliper was hanging up causing a pull to one side. just something to check. if youve already went through the normal steering intervals.
 

crazy4offroad

Equal Opportunity Destroyer
Joined
Jul 30, 2010
Posts
8,468
Reaction score
1,070
Location
West BY-GOD Virginia
First Name
Curt
Truck Year
1979
Truck Model
K-10
Engine Size
350/SM465/NP205
If your drag link angle is good I would blame the (more than likely Chinese remanufactured) steering box.
 

ChevyBoy84

Member
Joined
Oct 27, 2012
Posts
46
Reaction score
0
Location
Cedar Rapids, Iowa
First Name
David
Truck Year
1987
Truck Model
v10 silverado
Engine Size
350
i don't have a bind but my lifted (6 in. rc) K10 wanders but ik why cause my tires are wider then stock when driving on seal coated roads or even older asphalt that have been sunk in where a typical vehicle tire would be i just ride it out but in your case that's puzzling
 

87sierra

Full Access Member
Joined
Aug 18, 2012
Posts
172
Reaction score
4
Location
Pennsylvania
First Name
Paul
Truck Year
1987
Truck Model
Sierra 2500
Engine Size
5.7L 350 TBI
did you remove the air in the system when you instaled it
also check make sures the hoses are were they need to go ive seen them put on opposite
 

tjd50317

Junior Member
Joined
Nov 6, 2012
Posts
12
Reaction score
0
Location
des moines
First Name
tom
Truck Year
1983
Truck Model
k2500
Engine Size
350
had garage change calipers, problem did not start until pump went bad changed pump twice( oriellys pump) then pressure hose, and had garage change gear box. was doing same thing with old box and new box. thinking about putting better pump on?
 

smurph20

Full Access Member
Joined
Jul 13, 2011
Posts
2,063
Reaction score
23
Location
Clyde, Arkansas 72717
First Name
Brad
Truck Year
1986
Truck Model
K20
Engine Size
350/SM465/NP208/4.10's
How you gonna put the hoses on wrong the pressure hose screws in and the return is held on with hose clamps?
 

Latest posts

Forum statistics

Threads
42,452
Posts
916,385
Members
33,986
Latest member
bigcreek
Top