Search results

  1. snappchevy

    95 Chevy water in passenger floor board

    Hey all, my 1995 Chevy K1500 has leaking water into the passenger floorboard. Can’t find anywhere it could be leaking from. It hasn’t rained and the floorboard does not smell like antifreeze. Any info or suggestions would be greatly appreciated, thanks.
  2. snappchevy

    Body work for 77 K20

    Hey guys thinking about sending my 77 K20 in for some body work. It needs rockers, kick panels, fenders, hood, and the doors are beginning to rust at the base of them. Just wondering where I should get the metal for it. Original parts are hard to find where I’m at. Also I’m needing some vent...
  3. snappchevy

    6.0 LS to SM465

    Not sure if this is the place to post this, but to those who have swapped in a 6.0 LS in their trucks, what have you done for the transmission? Looking at my options here and was curious about the 6.0. I was wondering what all I would need to do for my 4 speed (SM465) to bolt to it. My truck is...
  4. snappchevy

    6.0 LS to SM465

    Not sure if this is the place to post this, but to those who have swapped in a 6.0 LS in their trucks, what have you done for the transmission? Looking at my options here and was curious about the 6.0. I was wondering what all I would need to do for my 4 speed (SM465) to bolt to it. My truck is...
  5. snappchevy

    Off-road bumper ??

    What off-road bumper are y’all using? Wanting to make my truck an off-road machine
  6. snappchevy

    K10 driveshaft

    Newbie question here, I have an 86 k10 (shortbed). I’m wondering the length of the rear driveshaft. No lift kit, it’s a stock truck. I believe it’s a 32 spline shaft. Thanks
  7. snappchevy

    Help with lifting truck

    I have a 77 K20 and an 86 K10. I plan on putting a rough country 6 inch lift kit on the 86, since it’s just going to be a beat around truck. My question is what all am I going to need to do? Do I need to lengthen my driveshafts? Will I need to drop my transfer case? I should mention that it is a...
  8. snappchevy

    6.6 duramax

    Anyone ever swapped a 6.6 duramax in your square? I have a 77 K20 and I found a local listing with a 6.6 lb7 duramax with trans and transfer case hooked to it. Thanks
  9. snappchevy

    Sheet metal

    What did everyone use to put in new rockers and floor pans? My truck is pretty rotten at the rockers and outer floor pan. I’m wondering if anyone has ever used this kit and if they have how they liked it? Also open to more suggestions on where I should get my sheet metal at, thanks
  10. snappchevy

    1986 K10

    Hey y’all I got a 1986 Chevy K10, I’m wanting to lift it 6 inches. I’ve been looking at the rough country lift kit and the skyjacker lifts. I was wondering what all I’m needing to do to the truck for the lift kit, I’ve heard that if you lifted the truck taller than 4 inches you’ll need to extend...
  11. snappchevy

    453t Detroit diesel

    Hey y’all, I’m looking to put a new engine in my k20, and was considering a 453t Detroit. Anyone have one of them and what transmission are you running with it? Would love to see some pics !
  12. snappchevy

    Best all terrain tire for your square

    I have a 1977 Chevy k20 and was planning on going with a 4 inch lift and 35 inch tires, just wondering what the best all terrain tire would be, and would like to see some pics of them
  13. snappchevy

    Bumpers

    A little before and after, don’t know who would paint a chrome bumper
  14. snappchevy

    Bumpers??

    Would bumpers that came off an 81-87 model work on a 73-80 model? I’ve got a nice set of chrome bumpers that came off my 86 model but I’m wanting to put it on my 77
  15. snappchevy

    Floor pan or patch?

    Have some pretty good rust near the doors on the floor panel, would patching it up work or should I just put in a whole new floor pan? Rockers are bad too
  16. snappchevy

    From Tennessee

    1977 Chevy K20 350,SM465,4.10 gears Gonna be a fun project
  17. snappchevy

    Shackle flip or rough country lift?

    Considering either going a 4 inch shackle flip with the HD shackles or using the 4 inch rough country lift kit, just wanted some input on what I should go with
  18. snappchevy

    Best lift for all purpose use

    Hey y’all I just bought my first squarebody. It’s a 1977 Chevy K20 350 4 speed. I plan on lifting it, I was wondering what lift kit would be best for riding and some off-road usage.

Latest posts

Forum statistics

Threads
42,126
Posts
909,676
Members
33,619
Latest member
SMC2224
Top