Search results

  1. J

    Hyrdaulic Slave Cylinder

    Yesterday was the coldest its been this year so far. I fired up my truck and noticed I had no clutch.....I check under the truck and see the slave was leaking fluid from the boot. Is it common for the temp change to cause leaks in hydraulic systems? Should I replace the slave and call it...
  2. J

    Fuel Problems, HELP!

    Alright first off I have an 84 k10 350 sm465 edelbrock 1406. Last weekend I took my truck out for wood. We went to some mountains near bye. One we get to the mountains, the truck starts running rough and I see white exhaust smoke, I know white smoke means water, but wouldn't I be burning...
  3. J

    Ball Joints

    1st off I searched the forum and found nothing on this. Google did come up with a lot of discussions but I'd rather get opinions from you peeps. I'm in the market for ball joints. I've used Moog on my commuter, and I've heard good things about Moog on 4x4 trucks. Problem is Moog will run me...
  4. J

    Rear Differential

    Let me start off by giving some info; I have an 84 Chevy k10 1/2 ton 350 with a 4 speed granny gear tranny. I'm running 33" tires on 15" rims (plan on going with 35") under a 4" suspension lift. So I opened up my rear axle this weekend and ran into this.... So the truck still runs...
  5. J

    Ticking Sound from Inspection Plate

    Well I got a ticking sound from the aluminum plate near the flywheel housing. The ticking starts once the engine warms up. Gets louder/faster when the gas in pressed. The sound also gets louder/different when I put some pressure on the plate. I'll be taking the plate off sometime this weekend...
  6. J

    Dual Exhaust system

    I'm looking to buy a Dual Exhaust system that runs from headers back. I have an 85 k1500 and I just purchased some long tube headers http://www.ebay.com/itm/160875426714?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649 I was hoping to spend about $200 (very low budget :bawl:)...
  7. J

    Brake Light

    Ok so just the other night I turned on my lights, I notice my driver side brake light isn't working. The tail light and bulb is operational but my brake light wont work. So I turn off my truck, restart it, turn on my lights and boom!! The brake light starts working. This has happened twice...
  8. J

    tough and squeaks when turning

    I replaced my tie rod ends and I'm worried I may have messed something up. When I turn all the way to the right, it gets pretty tough and it starts squeaking. I installed each tie rod end the same turns as it took to uninstall the old ones. On one tie rod end I was about 2 turns off. Could...
  9. J

    Steering Gear Box

    Ok so i had quite of a bit of play in the steering and I couldn't tighten the gear box anymore or the steering would get stuck. I was told that I needed a new steering gear box. I went to the salvage yard and bought one for $45 I just took mine off and the shafts dont match. Should I just...
  10. J

    Delco Remy Distributor

    Hey guys just thought I would put this up for sale here before I go to ebay. I dont know too much about this distributor other than it came with a 350 which came off of a GMC big truck used to haul. It was running solid with a 2bbl intake/rochester carb which I'm also looking to sell if...
  11. J

    Ball Joint Replacement

    I searched and couldn't find any replacement instructions, so excuse me if there is a similar thread somewhere. I took my 85 k1500 to get the tires aligned and was told I need to replace the upper and lower ball joints on the passenger side. I got a quote from a couple local auto repair...
  12. J

    Engine wiring/vacuum connections!

    Hello all, I'm new to this forum so here is my story. I have an 85 GMC k1500 which had a 305. I swapped it out for a 350 i scored at a salvage yard. They couldn't tell me what vehicle it came off of, all they knew was that it was a rebuilt 350. It came with its own carb, intake, distr...

Latest posts

Forum statistics

Threads
42,299
Posts
913,289
Members
33,799
Latest member
jp wessels
Top