Search results

  1. newbie17

    Dually Wheel Fitment Help

    Hey Big Chip-Things are going great here in Texas-How is it up in the "RUST BELT"?
  2. newbie17

    Seized Brake Drum '78 C30 - HELP!

    The factory Service Manual is your friend.
  3. newbie17

    Dually Wheel Fitment Help

    No offense, but---YUK!!
  4. newbie17

    Engine oil cooler hoses

    Yes! If I go that way I will make sure NO DORMAN. I would not want an oil line to blow or even leak.
  5. newbie17

    Engine oil cooler hoses

    Thanks Rickf. Yep, many people think I'm weird for wanting to keep my vehicles(trucks//cycles) as close to original as possible. However!!!!! that being said, going for the AN braided hose and anodized fittings is looking pretty good right now. I have been in aviation for 56yrs. and I'm very...
  6. newbie17

    Engine oil cooler hoses

    Thanks BillK and AuroraGirl. That looks like my oil filter adapter and oil cooler. The (2) Dorman hoses are for 4WD-won't work. I called LMC to have them measure the one line they sell. They replied this morning- the line is P/N: 32-1860 and is 39" to the 90 degree bend and 3.5" from the 90 to...
  7. newbie17

    Engine oil cooler hoses

    Sorry for not providing enough info. 5.7L. Has the factory adapter.
  8. newbie17

    Engine oil cooler hoses

    Searched for old threads on factory engine oil cooler hoses-found one from 2012. Poster did not find an answer. It's been 9 yrs. Anybody ever find a source for these hoses? Dorman only sells one of them. (625-617). I need the (625-616) also. Same goes for LMC. I need both hoses. I know I'm not...
  9. newbie17

    1983 C30 Dually

    I like any "ton"!!!!
  10. newbie17

    Plastic Vacuum lines

    Thanks 75gmck25. I just got back from O'reillys. Found the Dorman 1/8" tubing. Thanks for the informative and fast response!!!
  11. newbie17

    Plastic Vacuum lines

    This issue has probably been addressed before, but a GMSB search was unsuccessful. Is there a source for the small (1/8") plastic vacuum line on the firewall? It runs from a rubber hose connector to the passenger side firewall grommet into the cab and supplies vacuum for the vent actuators.
  12. newbie17

    Vent window assy.

    Thanks Craig85. Yes, changing the complete assy. from a '83 C10.
  13. newbie17

    Vent window assy.

    Will a 1983 vent window assy. interchange with a 1985 assy.?
  14. newbie17

    Fan Clutch debacle, manufacture information

    Yes, I agree with SirRrobynO, nice , neat install and clean engine compartment. I like stock, no frankenstein stuff.
  15. newbie17

    cam change

    Thanks SquareRoot, I changed the cam 28 yrs. ago and I cut the vertical brace and welded it back in place when done. Been so long my memory took a walk!!!! Don't know why the Serv. manual said to raise engine. Thanks wazzadakka94 I will be cleaning the inside.
  16. newbie17

    It’s official, I’m a nerd

    Frankenchevy, I apologize if I offended you in any way. This is the "other" vehicle category and I should have contributed something positive or kept quiet. Please enjoy your EV and good luck.
  17. newbie17

    It’s official, I’m a nerd

    O.K.-So you make enough money to buy-in to this EV crap! Yes, I should have said- I.M.H.O. Subjectivity is over-rated. What are some of your "other" vehicles? You will wake up(4-6-8 hours?)to a fully charged vehicle. I'll fill the tank on my truck in 5 min. and be back on the road while you...
  18. newbie17

    cam change

    Thanks Ricko1966. I am going to have my A/C system emptied with a recovery unit. The engine has only 40,000 mi. All else is o.k. Last week the engine felt like it had a miss at idle. I changed spark plugs-no improvement. Wires all good. Removed rocked covers-ran engine-noticed #7 cylinder...
  19. newbie17

    cam change

    1987 R30/5.7 TBI Exhaust valve cam lobe on #7 cylinder worn off. Going to replace cam/lifters. My GM Service manual says to "Remove front engine mount bolts and raise engine"-but it does not say how high. Can't go very high or the rear of the engine will hit the firewall. Has anyone out there...
  20. newbie17

    It’s official, I’m a nerd

    Electric vehicles are over-rated and over-priced. Short-range and take too long to re-charge. Get rid of fossil fuel? Where the heck do you think the electricity comes from to charge you're lame electric car????
  21. newbie17

    It’s official, I’m a nerd

    I think I'm going to be sick!!!!
  22. newbie17

    Gas tank pressure - air rushes out when the the gas cap is unscrewed

    The only poster that is correct is SirRobyNO. On the 1987, each tank sending unit has (3) hose connections: pressure, return and tank vent. If you have dual tanks, the left and right tank vent hoses are next to the fuel tank selector valve on the R/H side on the inside frame rail. The lines...
  23. newbie17

    So Does Everyone HATE This Steering Wheel?

    Yep El Perdido!! Had a cover on my '85 for over 30 yrs. When it starts getting kinda funky I just put on a new one.
  24. newbie17

    So Does Everyone HATE This Steering Wheel?

    All this crying about sticky stuff on the factory steering wheel! Clean it! I'm sure your truck has bigger problems that need attention.
  25. newbie17

    Just finished a in tank fuel pump replacement job, not the easiest job to do by yourself

    I love it!!! Pulling bed is the best way to do tank work, in my opinion. Dropping the tank method is good if you have 16 gal. tanks, but 20 gal. tanks-my arm is not long enough to reach the hoses. I just finished installing new pumps/sending units in both of my tanks(20 gal.). I pulled the bed...

Latest posts

Forum statistics

Threads
42,032
Posts
907,788
Members
33,528
Latest member
Hugger-4641
Top