Search results
-
starter rebuilding - advice needed
I have been using a starter that the 1997 Tahoe 350 uses on all my Chevy engines with the large flywheel 168 tooth , that most use . They have a reduction gear and are very reasonably on line . Just put one on my GMC works great .- Donald
- Post #15
- Forum: Electrical & Audio
-
Muncie 4 Speed In A Truck?
Stay away from Muncie's made in 63 they had no bushing under the 1st gear and can seize to the out put shaft under heave loads .- Donald
- Post #4
- Forum: Manual Transmission & Clutch
-
-
Header angle / ground clearance
I used 3/4 length headers gave all the ground clearance you need to keep exhaust inside frame rails .- Donald
- Post #7
- Forum: Tech Discussion
-
350 to 400 swap... Worth it?
I will make this short Yes, it is worth it, all the story's about 4oo's overhearing I have never had one overheat as long as you have a decent cooling system not a worn out clogged up mess. In fact, I have one sitting in my garage waiting for something to put it in.- Donald
- Post #14
- Forum: Engine & Performance
-
Am i calibrating this starter right?
Knckle Buster hit it on the nose , I always used a paperclip to check my starter gear cleanance .- Donald
- Post #6
- Forum: Engine & Performance
-
What new tools have you got lately?
I didn't get new tools but new toolboxes . -
Rear-end shot
A shot of my 31 Chevy with a Richmond quick change .- Donald
- Post #32
- Forum: Differential & Driveline
-
Myrtle Beach Run to the Sun Car Show
Any one wanting to go in 2024 make sure you register on line . If the sell out like this year you will not be able to register at the show . There where people buying window stickers from cars that where registered for as much as $400 . By the way my 1931 Chevrolet Hercules pick up won truck of... -
Long tube headers/dual exhaust question
Unless you are out for total performance I think an X or H pipe would be a waste of time.- Donald
- Post #6
- Forum: Tech Discussion
-
AMD Bumper...anyone purchase
I don't know if you need the complete bumper , I got the complete bumper kit with all the hardward from USA1 $529.95- Donald
- Post #7
- Forum: Paint and Body
-
-
What did you pay for a square
I payed $600 for mine 4 years ago .- Donald
- Post #76
- Forum: Tech Discussion
-
TH400
Sorry I meant a 700r4 plug your right the 4l60e has a different pass through many more wires . I have an excuse 79 years old .- Donald
- Post #23
- Forum: Automatic Transmission
-
TH400
Aurora Girl hit it on the nose some one put a 4L60E connector in this trans . I think monster trans did the rebuild . I ordered a new one , single pin . Thanks all .- Donald
- Post #21
- Forum: Automatic Transmission
-
No CRANK after rain......
You mite look at the distributor cap and rotor . Some of the after market caps collect moisture and HEI rotors can trace through and ground with condensation .- Donald
- Post #2
- Forum: Tech Discussion
-
Finished
# 8 was a little tight but got it on from under neith .- Donald
- Post #11
- Forum: Paint and Body
-
Finished
New stainless mid leight headers $118 on eBay's . They are for a 88-97 but fit this 85 perfect .- Donald
- Post #9
- Forum: Paint and Body
-
Stainless headers for C10 73-87 SBC
I just ordered and installed these headers that where listed for 88 - 97 in my 85 s1500 will fit 73-87. They fit great and at a very good price $118 . There are a shorty or mid length header and are not as good as full length headers but worked for me with a lowered truck . I wanted to keep the...- Donald
- Thread
- Replies: 1
- Forum: Engine & Performance
-
Anyone know what these rims are from?
Look like 37 ford wheel centers .- Donald
- Post #10
- Forum: Other Vehicles
-
Headers
Has anyone tried a set of header for a 88-97 c10 350 on a 85 c10 350 ???- Donald
- Thread
- Replies: 1
- Forum: Engine & Performance
-
-
Finished
After more time then I wanted I finality finished my 85 c15 , well really they are never finished . Last picture is before .- Donald
- Thread
- Replies: 10
- Forum: Paint and Body
