Search results

  1. N

    What have you done to your square lately??

    Frame off build 20 years in the making. Finally in paint.
  2. N

    New Here and could use some help 1982 K10

    We are in paint. After all these years
  3. N

    New Here and could use some help 1982 K10

  4. N

    New Here and could use some help 1982 K10

    Hey thanks for that! I found some at summit I am up in Ohio this week so I’ll swing by Akron and pick a set up! Thanks again.
  5. N

    New Here and could use some help 1982 K10

    Lol no biggie. Anyways no spacers on the top side of those bolts. Found a lowering kit which is just 4 steel bushings and also my transmission rubber mounts are mush so from what I’ve read on another forum that will help fix my issue. Can anyone confirm or deny that ? Thank y’all for the speedy...
  6. N

    New Here and could use some help 1982 K10

    Alright guys am not sure if there is a spacer on the other side of the frame but if so I will swap them to between the frame and the crossmember. Also is 2” of extension on the front drive shaft ok ?
  7. N

    New Here and could use some help 1982 K10

    The bolts you are referring to are the 4 bolts holding the crossmember to the frame correct? As far as the transmission mount it doesn’t look broken to me.
  8. N

    New Here and could use some help 1982 K10

    There is about a 1/4” of clearance between the top of the crossmember and the double joint cardin? on the drive shaft and about 1” of clearance between the drive shaft and the exhaust pipe. Also there is about 2” of extension on the front of the drive shaft where it slides in and out where my...
  9. N

    New Here and could use some help 1982 K10

  10. N

    New Here and could use some help 1982 K10

  11. N

    New Here and could use some help 1982 K10

    I will snap some photos in a few just got off work. As far as spacers. I do not believe there are any. Be back with photographic evidence ASAP.
  12. N

    New Here and could use some help 1982 K10

    hello all, I am at a complete loss. I have a 1982 K10 single cab long bed trying to put front drive shaft in after a 4” pro comp suspension lift. The rear end of the front driveshaft bolts up against the 4 bolt square pattern front yoke on the NP 208C diffential. The double joint part of the...
  13. N

    New Here and could use some help 1982 K10

    Can I PM someone with a drivetrain question I’m currently in a bind and I don’t know what to do.
  14. N

    Front Drive Shaft hitting crossmember Please Help

    hello all, I am at a complete loss. I have a 1982 K10 single cab long bed trying to put front drive shaft in after a 4” pro comp suspension lift. The rear end of the front driveshaft bolts up against the 4 bolt square pattern front yoke on the NP 208C diffential. The double joint part of the...
  15. N

    82 K10 Won't start

    Okay so....ya'll might laugh but swapped my battery out thinking it may be bad from being ran down and left dead for 2 years. Also changed the pos and neg wires they were taped and old and bare in spots. Anyways swapped it out and had changed the bad starter solenoid. Turns over like a champ...
  16. N

    82 K10 Won't start

    Update officially puzzled... Okay took the old starter solenoid to the parts store to get a new one asked him to test it. He stuck the cables on it and filled the store with smoke..had to laugh. Anyways swapped out the starter. As far as wiring I have the pos battery cable going to the top...
  17. N

    82 K10 Won't start

    2 minutes in total with 8-12 second bursts however it was just working the day before so if that is the case I will swap out the starter does anyone know what starter should actually go on there? I read half the time the part store will sell you a smaller one and it isn't strong enough. The one...
  18. N

    82 K10 Won't start

    Hey guys I'm new so I may not be posting in the correct spot. I combed the threads trying to self diagnose before posting this. Anyways truck was sitting for a year in storage. Charged up battery drained tank, filled tank back up, disconnected distributor wire to get the engine turning over...
  19. N

    New Here and could use some help 1982 K10

    Thanks for the insight guys! When you say changing the front clip do you mean just the front inner support or the front fenders as well? I've been milling around this site and am curious is there a parts swap or classifieds or something of the sort here?
  20. N

    New Here and could use some help 1982 K10

    Glad to be here! Thanks for the support and I think I will do just that with the wheels! I have been told 35" will rub with a 4" suspension lift on turns without a body lift which I think looks bad on a SB ..personal opinion. Am I wrong? I fell in love with the General Grabber Red letter anyone...
  21. N

    New Here and could use some help 1982 K10

    Hey Ya'll, My name is Josh and just found this site. I have a 1982 K10 I built with my old man about 12 years ago before I left for the service. I finally got ahold of her last year and I'm able to finish her now. Anyways so far frame of resto frame was por15 along with the underside of bed...

Latest posts

Forum statistics

Threads
42,068
Posts
908,354
Members
33,544
Latest member
Twistedgmt400
Top