Search results
-
What have you done to your square lately??
This truck has turned into an obsession Thanks! I Stared at that bumper in the catalog for long time and thought about that too...- R Carnella
- Post #15,215
- Forum: Garage
-
What have you done to your square lately??
Hi,I added the lower lights, also cut some holes to match the shape of the lenses(sorta). The bottom lights are for a 2006ish Tahoe/yukon i bought off amazon. I like them alot so far, i just hope they last awhile. The headlight lenses and wiring are from LMC, and the headlight bulbs are LED's...- R Carnella
- Post #15,213
- Forum: Garage
-
What have you done to your square lately??
I added some cool lights today. Hopefully i can see better at night. Don't want to blind anyone, but i need more light right in front down low.- R Carnella
- Post #15,210
- Forum: Garage
-
1991 suburban project
Welcome fellow burb lover,so much potential in these trucks I'm looking forward to seeing what you do with it. I looks very similar to my 1990 v2500 when i brought it home. I have since fully disassembled and reassembled to my liking lol.- R Carnella
- Post #19
- Forum: Introduction
-
So is this type of Bumper Trim unobtanium?
I searched for a few months, eventually gave up and just got new bumpers with no strips- R Carnella
- Post #13
- Forum: Exterior
-
-
New to the site from NC
Welcome from long Island, beautiful burb! Are those front seats original? I've never seen them before.- R Carnella
- Post #14
- Forum: Introduction
-
Kicking around doing an LS swap
Yes it for the ecm so trans will shift in low range, also indicate on dash just cause i can. The speedo and other info is serial data from the ecm.- R Carnella
- Post #31
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Kicking around doing an LS swap
O forgot to mention the shifter gate plate is very hard steel and almost impossible to drill through hence the epoxy.- R Carnella
- Post #27
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Kicking around doing an LS swap
RoryH19 what micro switch did you use and do you have any pics under the cover? Sorry no more pics but this is the switch I used. I just removed the shifter gate plate and epoxied the switch to the bottom side and positioned it just right. Then i just bolted the plate back on.If you look...- R Carnella
- Post #26
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Suburban crazy
Welcome can't wait to see more of your suburban! Here's my baby- R Carnella
- Post #14
- Forum: Introduction
-
Kicking around doing an LS swap
I run a 04 5.3 4L60E in my v2500 burb. I ran a micro switch down to my shifter that tells the ecm when im in low range otherwise low range will not work/shift properly- R Carnella
- Post #16
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
1984 K10 my new toy- I have owned since 1985
That's beautiful! Welcome.- R Carnella
- Post #16
- Forum: Introduction
-
New - Reproduction OEM Floor mats
I've been running these husky liners for a few years but those would look so much nicer!- R Carnella
- Post #34
- Forum: Interior
-
Vibration - Driveline Saga
Had a similar problem until i found a bent axle- R Carnella
- Post #24
- Forum: Tech Discussion
-
I bought some brand new headlight bezels and radiator molding. What total garbage!
I'll never buy anything from brothers again, had the worst customer service experience ever. They sent me the completely wrong bumper then blamed me for there mistake. Cost me over 100 bucks to send it back and waisted literally hours of time on hold of there ****** ass phone systems....god I'm...- R Carnella
- Post #14
- Forum: Exterior
-
Wiper motor always on.
Solving this issue would benefit the entire community.- R Carnella
- Post #13
- Forum: Gauge, Speedo & Instrumentation
-
Help with brake hoses
Be sure to inspect all your brake line for rust like this. Believe it or not this looked ok from the top looking down at it.- R Carnella
- Post #18
- Forum: Brakes
-
Educate me on sanders
Dual action & orbital are the same. There are two varieties, fine/short throw and course/long throw. You will need at least a fine/short dual action sander for finish work but preferably both. And when i say DA and orbital are the same I'm referring to all "rotary" type sanders if that makes...- R Carnella
- Post #6
- Forum: Garage
-
Hooker Exhaust Manifolds- I think I like em!
Yes my 90 v2500,hope these help.- R Carnella
- Post #17
- Forum: Engine & Performance
-
1988 5.7 to 1995 7.4 swap question
If it's a 4x4 Wouldn't your truck be a V2500?- R Carnella
- Post #4
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Hooker Exhaust Manifolds- I think I like em!
Wow that's a clean engine bay! I thought mine was nice...- R Carnella
- Post #15
- Forum: Engine & Performance
-
Hooker Exhaust Manifolds- I think I like em!
Think what you want about value $ but LS swapping my truck (5.3/4L60) was the greatest improvement I've made to this vehicle. I literally transformed my truck. It is a joy to drive, Sounds killer and gets almost twice to milage. Except for the rarest of rare all original.... i don't think a well...- R Carnella
- Post #12
- Forum: Engine & Performance
-
Rear wheelhouses for 1991 suburban square body
3rd seat fits fine.i regards of seat fitment the wheelhouse is only taller, so seat w/arm rest's fits between no issue. The only other thing that might be a small problem for some, would be reusing original wheelhouse molded carpeting...not sure though because i bought all new carpeting and...- R Carnella
- Post #9
- Forum: Paint and Body
-
Rear wheelhouses for 1991 suburban square body
Yes 22 year's.- R Carnella
- Post #7
- Forum: Paint and Body
Latest posts
-
-
-
-
4l80e conversion in 1985 suburban. What parts do I need?
- Latest: RanchWelder
