Search results

  1. D

    76 K10 rear main seal

    Is it a decent idea to just change all the rod bearings while the pan is down?
  2. D

    78 K-10 Dual Tank Install

    It had the old three port valve, with single power wire. I replaced it with the newer six port version, and when you do that, you have to completely rewire the valve and selector switch. I believe it has six wires instead of 1, if I remember correctly. There are a ton of threads on here about...
  3. D

    Wiring Harness journal

    Dome light fixture and socket replaced and working. Pass side jamb switch working, drivers is not. It's brand new but luckily cheap.
  4. D

    Making the Fuel System Simple

    FWIW - I installed an online pump with my Pro Flo 4 system originally. Stupidly, my first test drive was on an offroad trail in the middle of nowhere and it nearly left me stranded - the brand new pump kept overheating and I'd lose fuel pressure, needing to pull over every 10 minutes or so and...
  5. D

    Fuel Tank Replacement

    You don't have to get a new sending unit if yours is working, but I probably would. Replacing those is not fun, and you're going to have the tank down already anyway
  6. D

    Replace Steel Dash

    I actually saw the three dashes in the LMC magazine yesterday, which is what got me asking this question My dash is pretty mangled, especially around the steering wheel area. Most of the smaller, thinner braces are broken, bent twisted and dented, to the point where the wiper switch doesn't...
  7. D

    Replace Steel Dash

    How long would you say that took? And how hard to get lined back up properly?
  8. D

    Replace Steel Dash

    Old thread I know. Has anyone done this recently? I'm curious how difficult it would be to replace mine
  9. D

    78 K-10 Dual Tank Install

    I had the same thing happen with my 77 K10 a few years back. I was replacing the fule hoses, and I snapped the barbed end off the selector valve. I ended up replacing with the newer version and rewiring the valve.
  10. D

    Dakota Digital install with American Autowire harness- ETA adding TCI 4L60E control to the install

    DD makes a module for the Holley Sniper? I wasn't aware. I went with the Pro Flo 4 almost completely because I knew they made a module for it. If I knew they made one for the Sniper, things may have been different
  11. D

    Making the Fuel System Simple

    Can you disconnect the external pump and see if you still get fuel pressure?
  12. D

    Dakota Digital install with American Autowire harness- ETA adding TCI 4L60E control to the install

    This is awesome. I just about finished my wiring harness and am getting ready to instal the DD gauge set. Looks like you're a week or two ahead of me - I'll be keeping an eye on this thread for sure
  13. D

    Gas Gauge Problems Continue

    I replaced both my senders and tanks as well a few years back when I switched to efi. The tanks are meant for efi, and have baffles in them to keep sloshing to a minimum, but my cheap, tempo gauge still bounces around a bit. I think it has more to do with the gauge itself. The expensive, nice...
  14. D

    Horn contact

    Hello from the future. Thanks for the info, helped me get my horn working today
  15. D

    Wiring Harness journal

    I think I have short in my dome light socket, so ordered a whole new assembly from LMC. I got the shift linkage put back together this morning, as well as the steering wheel with horn contact parts and installed two new Hella horns
  16. D

    Tail light brake light issue

    The grounds are just behind the tail light lenses
  17. D

    Steering Column Advice

    The turn signal switch has some little springs in it that are responsible for returning the turn signal lever back to the middle position. If one of those is broke, the lever won't return. I know they make replacement springs. The switch itself is not all that expensive and not crazy difficult...
  18. D

    Wiper washer motor replacement. Who you buying from?

    Pretty much - thanks for the replies
  19. D

    Wiper washer motor replacement. Who you buying from?

    Did that motor wire up to your existing wiring and switch, or did you have to retro everything?
  20. D

    Wiper washer motor replacement. Who you buying from?

    Any way you have a link to the one you bought?
  21. D

    Wiring Harness journal

    Couple weeks more gone by, and getting close to buttoned up. I've taken her for a few spins around the block. I thought it'd be fun to list a few of the screw ups I made during the process - I had the fuel pump power wires wired into the sending units. Kept popping a fuse every time I turned...
  22. D

    Brights pop fuse

    I was just trying to get some help with a fuse
  23. D

    Brights pop fuse

    A few pics of the manual that came with the harness, as well as the fuse box mounted. The fuse labeled Headlights is the one that kept popping previously, before I moved the high beam indicator wire that was shorting
  24. D

    Brights pop fuse

    Very nice article, definitely clears up questions on how that works. Since the headlights aren't running through a fuse, what's the purpose of the headlight fuse?
  25. D

    Brights pop fuse

    The terminations were all pre-made on the wiring harness. Everything works correctly now after isolating that high beam indicator wire

Latest posts

Forum statistics

Threads
45,954
Posts
996,851
Members
39,154
Latest member
cmcqueen
Top