Search results

  1. G

    Cruise control works for a while then starts to lose speed

    most of the issues with not holding speed that I've had have been vacuum related. if you can't set the speed or you lose the speed setting when you touch the stalk, my issues have been switch related. the servo and module under the dash have never given me issues, yet (fingers crossed)
  2. G

    TBI Issues

    Getting ALDLDroid from the Google playstore (about $20) and a Bluetooth ALDL reader from 1320 electronics or Red Devil River (about $90) is what I recommend. I think 1320 may also have a free app you can use.
  3. G

    Charging issue

    are you measuring at the battery or using the gauge? on my 1990 burb, the gauge reads about half a volt lower than what is shown at the battery with a voltmeter. also, my ECM readout from ALDLDroid for voltage shows what the gauge shows, also about a half a volt lower than the battery. I am not...
  4. G

    Intake Manifold Install

    you could pigtail a new ICM connector in, sure. the large harness is a pain to see., but I had a small spot that rubbed through on the cruise control bracket that caused me headaches with the ECMB circuit. a bright flashlight has helped me find rub through because the wire is usually very...
  5. G

    TBI Issues

    if it is dumping too much fuel, check the coolant temperature sensor. if it goes bad, it can default to low temp and it makes it run super rich. ALDLDroid and a blue tooth ALDL reader helps a bunch for diagnostic on TBI
  6. G

    87 Custom Deluxe 30 shut off while idling.

    lost power to everything or just the ECM? are the ECMB and ECM1 fuses OK? does rhe check engine light up when you turn the key to on?
  7. G

    Intake Manifold Install

    if it hiccups and the light came on, the code was set again. clearing codes can be done by disconnecting the negative battery terminal. but it sounds like you have an intermittent issue. check the ICM harness up against the firewall to make sure nothing is rubbed through. check to make sure no...
  8. G

    Intake Manifold Install

    it will store codes for about 30 starts. but if the code came back after your parts replacement, and may be intermittent, that seems to point to a bad connection or maybe a wiring issue somewhere in the ICM harness.
  9. G

    Intake Manifold Install

    yes, has to be an issue in EST or the 2 reference wires from ICM. that's the only things that will set code 42. could also be a problem at the connector plug at the ICM or the EST wire. Diagnostics in post #65
  10. G

    Cruise control works for a while then starts to lose speed

    I'd just replace all the vacuum lines under the hood as cheap insurance, verify the check valve off the manifold line is working, and make sure the vacuum reservoir holds vacuum. if that all checks, you will have to look closer at the servo pod to make sure it holds a vacuum. I've seen YouTube...
  11. G

    Cruise control works for a while then starts to lose speed

    mines a 90 and is still is a vacuum system, although there is an electrical control box that is between the switch and the vacuum servo pod that tells the servo what to do. not holding speed is most likely a vacuum issue in my limited experience. chapter 9 of the GM service manual covers...
  12. G

    Cruise control works for a while then starts to lose speed

    agree, sounds like it is having an issue holding vacuum. check the hoses and the vac reservoir on the driver side fender under the hood in addition to the pod that attaches to the throttle.
  13. G

    Issues with seatbelts

    rough cost and turnaround time?
  14. G

    Intake Manifold Install

    I've used the paste it comes with normally. no issues with early failure of AC Delco
  15. G

    Intake Manifold Install

    make sure it is an AC Delco. it's a common failure point and I carry a couple spares in the truck at all times...
  16. G

    Need ideas for a modern steering wheel.

    yep, that's what I have! my burb was equipped with just about every option, so it is not surprising that the wheel was an option.
  17. G

    Need ideas for a modern steering wheel.

    I like the wheel on my 1990 suburban. I think 88-94 are all the same and likely are a direct replacement.
  18. G

    Intake Manifold Install

    if it wasn't doing it before you replaced the manifold, and is new after, it is likely something that got touched somehow. I'd guess the issue to be in the ICM harness in the EST wire or one of the 2 reference wires. the issue could be in the wire or the connectors themselves. did you go through...
  19. G

    Intake Manifold Install

    I don't think plugged EGR will result in 42. it will eventually throw a code when it self tests at highway cruise. but I think it is 32
  20. G

    Intake Manifold Install

    is it still code 42? because if it only does it at operating temp (likely when it hits closed loop), it makes me think it may not be ignition related.
  21. G

    Intake Manifold Install

    I'd still look at the vac hoses. the cannister, PCV, EGR solenoid, and MAP sensor should all come off different TBI ports. some are manifold vac and some are ported vac and it probably matters that they are all on the right ports. that might not be the issue, but while you are messing around may...
  22. G

    Intake Manifold Install

    did you try to follow the diagnostics for code 42 in the drivability manual?
  23. G

    Intake Manifold Install

    what is this vacuum arrangement? looks like something that should be hooked up to the TBI is Teed into the PCV valve line?
  24. G

    Best brand for LED conversion?

    I dont have pictures of the trimming. you only have to trim to fit a 90degree bulb. if you use the straight 9006xs and 9005xs straight bulbs they come with you don't have to trim at all. I still run the 9005xs in the highs because they are actually plenty bright and you would also have to trim...
  25. G

    Best brand for LED conversion?

    not a lot of support for 89-91 given the odd size and limited years of use. the LMC housings with glass lenses with the adjuster buckets trimmed to fit a 9012 bulb is a good option that I am running. I have thought about dropping in a diode dynamics SL1 LED bulb, but haven't bit the bullet yet...

Latest posts

Forum statistics

Threads
45,947
Posts
996,683
Members
39,143
Latest member
ash73
Top