Search results
-
What have you done to your square lately??
Well, I’m against the grain. Put them diagonal. -
What have you done to your square lately??
Looking forward to seeing if it is better now! -
****CAUTION, PLEASE READ****
I’ve not had a problem here, but when I first had an instagram account, I almost got taken by a guy selling a dash pad that was too good to be true. Turns out you can find out how many times an Instagram account has changed their name. I went back and looked and this person had changed names 10... -
-
Another response to ***CAUTION, PLEASE READ ***
Welcome from the far upper NW corner. Nice truck!- ChuckN
- Post #21
- Forum: Introduction
-
What have you done to your square lately??
Man, that is gorgeous. Nice work! -
Topic for GMC Sierra California Sundancer owners
Nice find! Thanks for sharing. -
What have you done to your square lately??
Thanks for the info, I appreciate it. Mine is going to Skagit Transmission this morning and is being sent to a custom shop where it’s going to be redone to the tune of 2200-2500 rpm. I don’t recall the name of the place he sends it to but I will post it here if I remember to ask him this... -
What have you done to your square lately??
Project stall converter engage. -
TH350 Removal
Yep, got one. I figured I’d drop the pan and check for clutch material while I’m taking it out. I have a pan with a drain plug and used a Moroso reusable gasket.- ChuckN
- Post #16
- Forum: Automatic Transmission
-
-
TH350 Removal
Getting ready to pull my trans out for the torque converter change. So, 6 bolts, trans lines, disconnect/remove crossmember, remove distributor cap for clearance, support rear of engine under pan with wood block/jack. I’d imagine I’ll need to disconnect exhaust, maybe remove headers. What else...- ChuckN
- Post #11
- Forum: Automatic Transmission
-
Turbo350 w/shift kit slamming 2nd gear
https://www.streetsidetools.com/mobile/product.aspx?ProductCode=sst%2D0814%2Dc&404;http://www.streetsidetools.com:80/SST-0814-C-Accumulator-Pry-Bar-with-Bolt-p/sst-0814-c.htm= $35 here.- ChuckN
- Post #80
- Forum: Automatic Transmission
-
-
What have you done to your square lately??
Hmm. I could be wrong, but there probably isn’t a lot of torque converter custom guys, could be the same one. -
-
What have you done to your square lately??
Darn it! I was gonna give him my spare feathers to go along with it! -
What have you done to your square lately??
Spent a good amount of time inquiring about stall converters today. Then it dawned on me to stop by the driveline shop that did my rear end. Rich said he purposefully steers clear of transmissions, but pointed me to a gentleman at Skagit transmissions. I told him my setup and he recommended a... -
Carb Adapter
Lots of good info here. Keep in mind that Edelbrocks use no more than 5-6 psi of fuel pressure. I splurged and bought all the accoutrements from Edelbrock to avoid having to piece everything together. Edelbrock fuel pump (psi set for carb from factory) an AN line/braided hose that threads...- ChuckN
- Post #13
- Forum: Engine & Performance
-
Hello everybody!!!
Welcome from the Pacific Northwest! Nice rig!- ChuckN
- Post #15
- Forum: Introduction
-
What have you done to your square lately??
Looks like you’re exempt. https://www.dmv.virginia.gov/vehicles/registration/emissions#:~:text=Vehicles%2025%20years%20old%20or,required%20when%20renewing%20these%20registrations. -
What have you done to your square lately??
Doesn’t *look* that bad. Get that clamp off and then give it a good wiggle. Just depends on how much the crimp created by the clamp wants to hold on. You could try a thin punch/chisel to try to spread the pipe back out, maybe heat it up some too. -
What have you done to your square lately??
That’s a great response, I’ll give that a try. A looser converter is on the list as well. -
What have you done to your square lately??
The stall is too tight and stock. That’s for sure. Three degrees? Which direction? I called Edelbrock and they told me to put it back to ported timing, and back the advance off to 10-12 initial. Snowing and cold here, no way to test on street for a while. Mostly, I think he was just trying to... -
What have you done to your square lately??
True that- but then I got to thinking, a cam is much more than lift- it’s also duration, duration at .050, and just as importantly, overlap. It’s somewhat likely that I’d be able to guess based on lift what cam is in there, but at this point it is what it is, and nothing but me can change it...
