Search results

  1. O

    Missing exhaust manifold bolt, whats size

    Missing a bolt, what size, hole was there for a reason at one time but I forget.
  2. O

    It could have been worse

    Thanks for the being reply, yeah part of the stub was still on the rim. Thanks for all the advice,
  3. O

    It could have been worse

    Driving home, no issues and suddenly fighting to keep her straight and outta the ditch. Seems the spline sheared at the hub, easiest way to repair ? replace spline, look for a used rear and do the whole lot, 90 v1500, 3.73 rear.
  4. O

    What have you done to your square lately??

    A little headliner work, not perfect but fine for the likes of me.
  5. O

    Need help with regards rear ac

    Well I suppose if I wasn't a dumb ass I might have figured it out, thanks for all the help guys. Looked at my shroud and you there's the pipe.
  6. O

    Need help with regards rear ac

    Guys thanks for the replies and the further I Look ad dd1990 states it's the drain hose, unfortunately I have no idea what it connects to or if I accidentally tossed the fitting. Are the holes in the corners the drain vents?
  7. O

    Need help with regards rear ac

    Decided to do my headliner, as the vehicle isn't my daily driver this was a long time project with a vacation in between. Well I went to put the rear panel in and I realized that something was missing. The hose with the clip about 4 inches down was attached to something and I have no idea, there...
  8. O

    Headliner what to do

    Well I removed the headliner as the sagging was finally getting to me. No issue getting in down, was thinking of options when I decided I would roughly clean the front one (suburban). Removed the old headliner and foam material, the outside towards the roof had some foam as well. Some bowing but...
  9. O

    What am I doing wrong

    Changing out the rotors, when I was at it, done seals bearings etc, used the old hubs not issues except when putting on the warn hub, the final snap ring won't seat.
  10. O

    Spider gear reinstall?

    Changed out leaking rear axle seal, so I done both sides and bearings. No issues with that, unfortunately during the process the two spider gears came out. And I am having a hell of time reinstalling them, what's the trick. Thanks
  11. O

    Cross pin bolt snapped

    Changing leaking rear axle seal, go to remove the cross pin and it's snapped, anyone any suggestion other than they kit skyway sells. Thanks in advance.
  12. O

    Adhesive on barn door rubber

    Got some replacement rubber from Jon Addington, (Precision rubber) now the question is should I use a little adhesive as well in some places
  13. O

    Water on drivers floor

    Ya I was able to run a piece of taped wire (so I could see it) from the top down and also from the bottom up. Carpet backing is toast, so next step is I might as well do the front carpet. Thanks for the help.
  14. O

    Water on drivers floor

    Is this the drain, foam was mentioned, I ran some soft wire from the to down and this is where it came out.
  15. O

    Water on drivers floor

  16. O

    Water on drivers floor

    Ok, there's doesn't seem to be a leakage this stage, but if I overwhelm it, these two screw holes for the kick panel weep a little. It's barely noticeable but there, thoughts would this be just water that ingressing thru the open holes as it makes it way out.
  17. O

    Water on drivers floor

    Have fun lenght running boards, so probably that's a d8fference, water seems to be flowing well.
  18. O

    Water on drivers floor

    Yip removed these plastic panels, seems pretty good so far. The search continues.
  19. O

    Water on drivers floor

    Well I knew I had a leak, the burb had been sitting long enuff. Removed the carpet from the driver's floor, mass backing soaked. Removed cowl, cleaned up around it, obviously going to reseal joint to help the situation. Ran the hose and saw there was a small leak in this area, but obviously...
  20. O

    Guidance, ideas

    Recently installed a wireless backup camera in my 90 suburban, auto vox brand off Amazon. Installation went fairly easy, tapped into the reverse lights power for the camera. The monitor simply plugs into the cigarette lighter and comes on when I move her into reverse. Well installed yesterday...
  21. O

    Exhaust manifold question

    That was probably it, no heat riser valve was on it.
  22. O

    Yet another fuel gauge question

    Starting to troubleshoot my fuel gauge problem. Gauge reads past full, starting at the rear. Should I get a ohms reading from the purple/pink wire. Fuel sending unit is a delphi.
  23. O

    What have you done to your square lately??

    An old Warn trans4mer, price was right so it had to be got.
  24. O

    Exhaust manifold question

    Well I thought this might be easy, considering no broken bolts or studs, but no. Got a replacement, and yes it the same except for the flange where it meets the y. Well the y pipe is this and it seems that the replacement is too long or is this a removable sleeve in the y pipe. Any suggestions...
  25. O

    1990 suburban V1500, DRAC location

    Many many thanks

Latest posts

Forum statistics

Threads
45,558
Posts
986,230
Members
38,644
Latest member
FenderBanger
Top