Search results
-
-
upgrading 1" rotors
Do you have standard brakes or power brakes?- CRM
- Post #7
- Forum: Suspension, Steering & Brakes
-
My stereo install
I cut the foam board to size. Glued the vinyl to it and slid both pieces behind the base. I loosened the base up enough to slide them in then tightened the base back down to secure them. Sound-wise the only difference was a little more bass. It does looks a little more professional too.- CRM
- Post #12
- Forum: Stereo & Entertainment Systems
-
My stereo install
I found this piece of 2" rigid foam in the scrap pile at work today and I thought it might be cut to enclose the open ends of my amp/speaker base I installed. It should be very easy to install. I'll post a picture and whether it made the speakers sound better.- CRM
- Post #10
- Forum: Stereo & Entertainment Systems
-
Electronics are dropping like flies!
Sounds like you'd better start checking all ground terminations. Symptoms indicate a loose, or corroded, connection.- CRM
- Post #2
- Forum: Tech Discussion
-
MC leak. Rebuild or replace?
Took about 1.5 -2 hours but I got it done. I didn't change out the hoses as they checked out pretty decent. The old brake fluid was really black. -
What have you done to your square lately??
Replaced the leaking Master Cylinder and flushed the entire system. The brake fluid came out black, it had been so long since it was last done (probably 10 years ago at least). Took a whole large container of DOT-3 to actually get all 4 lines to bleed clear. -
What have you done to your square lately??
With the seat all the way back there's a gap of about 2" -
MC leak. Rebuild or replace?
I've ordered the master cylinder from Rockauto. It'supposed to arrive before the weekend. I'm going to do a complete system flush, because the fluid hasn't been changed in the 9-10 years I've owned it, and it sat in the field for 7-8 years. Might change out the rubber hoses while I'm at it. -
-
-
My stereo install
They sound great . I might try enclosing the sides if they'd sound even better. It wouldn't take much to make it happen.- CRM
- Post #9
- Forum: Stereo & Entertainment Systems
-
My stereo install
I finished it up. I went ahead and bought some edge trim because once I got it up and running, the metal was vibrating against the cab wall. After adjusting the amp my wife could hear the music in the house with the volume up 50%. PIC 1 is the 12v power wire penetration into the cab. PIC 2 is...- CRM
- Post #7
- Forum: Stereo & Entertainment Systems
-
My stereo install
Sprayed the metal with Nashua 357 adhesive. Installed the vinyl and trimmed the excess off. I am going to eventually install some Clear door edge molding around the edge of the metal base to protect the edge of the vinyl and to prevent the vinyl from coming loose. Installed the speakers, amp...- CRM
- Post #5
- Forum: Stereo & Entertainment Systems
-
My stereo install
Got the speaker and wiring holes cut out today and located some plastic bushings for the wiring holes. Tomorrow I'll glue down the vinyl, mount the speakers and amp, and see if I can get all the wiring run.- CRM
- Post #4
- Forum: Stereo & Entertainment Systems
-
Sliding Window
You might check youtube. A lot of good videos on their website.- CRM
- Post #3
- Forum: Glass & Mirrors
-
My stereo install
Picked up a wiring kit at Walmart also.- CRM
- Post #2
- Forum: Stereo & Entertainment Systems
-
My stereo install
I recently installed a pair of BOSS 4 x 10 speakers in the cab corners. I have purchased a BOSS 800w amp direct from the BOSS website. I have a pair of Pioneer 6 x 9 speakers which were installed when I had the original system installed a few years back. I've removed them from their original...- CRM
- Thread
- Replies: 12
- Forum: Stereo & Entertainment Systems
-
-
MC leak. Rebuild or replace?
The real question is: is Ronald's a JB1 or a JB3 ??????? -
MC leak. Rebuild or replace?
Since it's not a daily driver I think I'll just go with standard brakes. My only question now is do I have JB1 or JB3 ? My RPO code sticker doesn't say. I've looked at different tags around the truck but nowhere do I see it. I don't tow anything, or even carry anything heavy, so I think JB1... -
MC leak. Rebuild or replace?
Went out to the farm that had the 3 Sb's. Wow what a pile of junk! -
MC leak. Rebuild or replace?
Just found a guy on Craigslist that lives about 15 minutes away who has 3 '79 SB's he wants to part out. Going by after work to see what he's got. Maybe there's a power brake package available. Do I only need the power booster and MC or do I need additional parts? -
MC leak. Rebuild or replace?
I just might have to visit the You Pull It yard. -
MC leak. Rebuild or replace?
I'm actually going to buy the whole MC but I'm seeing bore sizes of 1" and 1 1/8". Maybe I'll pull the existing one and take it with me to the parts store.
