Search results

  1. Ronno6

    Engine stand block mounting

    I used the top 2 and the bottom 2 on my 4 wheel stand.
  2. Ronno6

    Engine stand block mounting

    My 350 block is mounted to my engine stand, but is very top-heavy. Makes it really difficult to roll over to top side up. Lower mounting arms just about parallel with ground. How balanced should (can) the block be when it is mounted? I would have to think that the condition will only get much...
  3. Ronno6

    Cam decision

    You might consider giving Willhoite's Cams in OK city a call...he fixed my up with a LT4 Hot Cam regrind for about 1/2 the price of new, every bit as good and can grind one to your specs.He may even be good with recommendations, not sure. But, wouldn't hurt to give 'em a call.......
  4. Ronno6

    Roller rockers,poly locks and valve covers

    I received my Scorpion 1001 roller rockers today. Amazon had them for just under $200.00 I tried to get Summit to price match per their policy, but the guy said THEIR number was "SCP1001" And was a newer model, but didn't know what the changes were. He did give me Scoprion's phone #, so I called...
  5. Ronno6

    Identify intake

    Kinda sorta looks like this one tome: https://www.summitracing.com/parts/nal-10185063 That's a great performing manifold..........
  6. Ronno6

    Elgin Parts

    What the heck to you use for a vaccuum source??
  7. Ronno6

    vortec heads on 350

    What RPM range do you need? For gobs of low end torque, the dreaded "swirl port" heads do a great job and are usually available for cheap, but they somewhat choke things off above 4000 or so. Swirl ports do a great job throughout the power band, I believe, but, if you opt to go with them. either...
  8. Ronno6

    Roller rockers,poly locks and valve covers

    Apparently, due to reduced friction, they give a bit of an increase in power and reduce heat. As I am using a roller cam and lifters, seems kind silly to cut the last corner........
  9. Ronno6

    Which Roller Lifter??

    The information on available roller lifters confuses the heck out of me! I need roller lifters for a Gen1 350 880 roller block. I see lots of lifters for LS motors, some LT motors and all variety of year ranges. Are there differences among the various roller lifters for small block Chevys??
  10. Ronno6

    Roller rockers,poly locks and valve covers

    Good 2 know. Are there good ones and bad ones?? (full roller rockers, that is...)
  11. Ronno6

    Elgin Parts

    Anyone using Elgin valve train stuff?? I am looking at their SS roller rocker arms part # SSR1840RS Seem like good stuff, but not very expensive...............
  12. Ronno6

    Piston Ring Gap Placement

    And that flies in the face of the Sealed Power diagram...which shows the same ring for all pistons, but the left bank will be opposite the right bank in relation to the engine centerline.That is to say, top ring gap to the top on the left pistons, and bottom on the right pistons, and so...
  13. Ronno6

    Piston Ring Gap Placement

    Trying to establish the orientation of ring gaps on the piston of my 350 is yielding a variety of results. Sometimes they are located top/bottom, with RH bank being one way, LH being opposite. Basically setting up all pistons the same, regardless of where they go in the block. Other information...
  14. Ronno6

    Roller rockers,poly locks and valve covers

    Are trunion style rockers much better than stamped steel,OEM style ball pivot roller versions?
  15. Ronno6

    Roller rockers,poly locks and valve covers

    Retrofit roller lifters are longer than either flat tappets or OEM roller lifters, hence the need for shorter push rods. I am building a roller ready "880" block with stock roller lifters. I have not read anything about roller rocker arms needing push rods of lengths differing from stock, but...
  16. Ronno6

    Roller rockers,poly locks and valve covers

    Thanks, Roger. Good to know. Thanks also to you, Bruce. I can afford that....
  17. Ronno6

    Roller rockers,poly locks and valve covers

    Not exactly...just don't wanna spend the coin for tall rocker covers if I can avoid it. I have considered using self locking nuts ala stock, but have read too many reports of then backing off.
  18. Ronno6

    Roller rockers,poly locks and valve covers

    Do roller rocker arms and poly lock nuts fit under factory rocker covers?? Are they all the same height, or are some shorter than others?
  19. Ronno6

    DD 350 Cam Suggestions

    I opted for the LT4 Hot Cam and purchased one reground from Willhoite's in Oklahoma City. He ground it with a built in 2° advance and instructed me to install with timing marks aligned per factory. I will still degree the cam when installing so I know what I have. We'll see how it goes.....
  20. Ronno6

    DD 350 Cam Suggestions

    So far, the engine is shaping up like this: 1984 C10 Stepside. Weight approx 4000lbs. (alum heads and intake will help) Vacuum power brakes. 350 2 bolt bored .030 over. 10:1 pistons mechanical fuel pump. Aluminum heads 2.02 intake 1.6 exhaust 64cc chambers 185cc runners 7/16 screw in studs...
  21. Ronno6

    Vortec vs Swirl Port spark Plug Location

    I'm gonna be using Hedman long tubes...
  22. Ronno6

    Vortec vs Swirl Port spark Plug Location

    Manifold spreader to install the manifolds...or spark plugs?
  23. Ronno6

    Vortec vs Swirl Port spark Plug Location

    Having read that the spark plugs on Vortec heads are offset towards the exhaust ports causing problems with some headers, I looked at the 193 heads on currently on the engine. The plugs are likewise offset towards the exhaust ports. I loosely test fit the headers to see if three was going to be...
  24. Ronno6

    Marine Vortec Heads

    Are there differences between marine vs. automotive Vortec Heads??
  25. Ronno6

    Motor s/nsticker

    Back there I found block # 10243880 along with date code A307 and identifiers 57LG The serial # sticker was on the flat shelf of the block in front of the passenger side head.

Forum statistics

Threads
45,565
Posts
986,345
Members
38,653
Latest member
82SquareBurb
Top