Search results
-
Rare Hood Ornaments, Wow! $$$$
That's up there alongside the Boss 429 stratosphere. -
Header farts
I don't use gaskets on cast manifolds but never tried it on headers, interesting. Might try that in the future.- fast 99
- Post #8
- Forum: Engine & Performance
-
Carb at high alt
Carter-Edlebrock metering rods can easily be changed. You will need larger rods. How much reduction in fuel? Someone will come along with the calculation.- fast 99
- Post #2
- Forum: Tech Discussion
-
Header farts
Above is an absolute, recheck recheck recheck. Suggest applying a small bead of high temp silicone to both sides of the gasket, let it set up for 15-30 minutes, install. Just snug bolts up and come back the next day and tighten. Also, cheap headers usually do not have a thick enough flange...- fast 99
- Post #6
- Forum: Engine & Performance
-
Brakes
Agree with the possible diagnosis. Question replacing the valve unless it has some other obvious issue. Read several posts about new PV's leaking or just plain failing. One failure was on a TV series, leaked. Most of the valves are offshore production.- fast 99
- Post #4
- Forum: Tech Discussion
-
1987 454 TBI down on power, runs good otherwise
Plugged exhaust? Drive with a vacuum gauge shouldn't go much lower than 4 inches. Alternate method loosen the header pipe slightly. Low fuel pressure?- fast 99
- Post #3
- Forum: Tech Discussion
-
What’s the solution to this?? Idle adjustor
Need a scanner or equipment to access the ALDL data.- fast 99
- Post #7
- Forum: Engine & Performance
-
What’s the solution to this?? Idle adjustor
Would be better to properly diagnose the problem. Really need to know the IAC counts. If you close the throttle plates to fix a cold start issue it could have a sticky throttle or die when warm. The IAC can only adjust so far then other undesirable things will happen. Some possible suspects are...- fast 99
- Post #5
- Forum: Engine & Performance
-
2 Tone on 83 C30
everything will fit except the front fender trim. Could break the color at the fender horizontal crease and carry the color back without trim.- fast 99
- Post #2
- Forum: Paint and Body
-
Edelbrock accelerator pump
Put the old coil back in and does it have the strap ground? I know people are trying to improve their vehicle, but the quality of parts today is sometimes questionable. On top of that a stock HEI coil can usually produce twice the KV necessary for combustion.- fast 99
- Post #6
- Forum: Carb Fuel Systems
-
Pass power window
Assume the question is what's wrong? Need to check power at either the switch or motor whatever is easier first. Then proceed uphill or downhill to the problem. Been repeated here numerous times, new parts are suspect until proven otherwise. Lots of junk out there.- fast 99
- Post #3
- Forum: Electrical & Audio
-
No drill,no ream, DIY Quadrajet throttle bushings
Interesting, Re-bushing like it has always been done isn't hard but at the very least requires a reamer. Can see where that might be a good option for one-time rebuilders.- fast 99
- Post #2
- Forum: Tech Discussion
-
Computer Control Quadrajet rebuild
and require special tools- fast 99
- Post #4
- Forum: Carb Fuel Systems
-
Went to the candy store today...no sweets today, but...
Wouldn't have enough money left to pay the electric bill. -
Flex plate
Agree, no It can be changed by sliding the tranny back slightly on alignment bolts/dowels. Use a long box end to remove the bolts.- fast 99
- Post #5
- Forum: Transmission & Transfer Case
-
Hey...what's the big idea..??
There are several people here than can assist with q jets. Do agree, decent carbs for non-HP applications. They get a bad rap from the lack of knowledge folks. Some of that might be related parts availability.- fast 99
- Post #4
- Forum: Engine & Performance
-
Vacuum diagram
Need the pu Depending on application may need the pump for AC doors or cruise. Unsure if a GM diesel was made with vacuum power brakes but that's another one.- fast 99
- Post #3
- Forum: Tech Discussion
-
Oil pressure sender switch and coolant sender what type of thread sealant to use since your not supposed to use Teflon so it can ground correctly
Have used liquid Teflon for decades never had an issue.- fast 99
- Post #2
- Forum: Tech Discussion
-
Wheel spacer for my 1986 GMC K3500 3+3….
Spacers? Your liability and life. Hopefully someone else won't get killed.- fast 99
- Post #10
- Forum: Wheels and Tires
-
Wheel spacer for my 1986 GMC K3500 3+3….
No, never, especially on duals. Sounds like you need to buy a different set of tires.- fast 99
- Post #2
- Forum: Wheels and Tires
-
Factory smoke
Hooking up a battery backwards can cause all sorts of electrical gremlins. Yes, it's possible damage was done to either the wiring or gauge itself. -
NAPA Power Steering Pump?
Usually Rock auto has a good selection with known brands but not this time. Just looked they have lars and BBB whoever they are and Cardone. Provided you're not doing damage by pounding on the pully I would buy a seal and be done with it. Been dealing with this crap for at least 20 years. Much...- fast 99
- Post #2
- Forum: Suspension, Steering & Brakes
-
temp sensor
Easy way to find out, remove it see what ya dealing with.- fast 99
- Post #5
- Forum: Engine & Performance
-
What atf fluid needed
Dex 3, Dex 6 or Dex Merc all will work. Of course, Dex 6 is synthetic and take heat better without breakdown.- fast 99
- Post #2
- Forum: Transmission & Transfer Case
-
temp sensor
To me that appears to be a broken off mechanical sensor bulb. I believe the original sensor will fit the larger diameter hole.- fast 99
- Post #3
- Forum: Engine & Performance
