Search results
-
P
Hello from Savannah, Georgia - 1986 C10 Silverado
Welcome from Bloomingdale/Faulkville Georgia. We are almost neighbors! Roebling Road Raceway borders my neighborhood. This forum is awesome. Pictures are mandatory- Poppy 87
- Post #16
- Forum: Introduction
-
P
What have you done to your square lately??
The most important advice I can provide to you regarding automatic transmission internal repair is clean, clean, clean! When you think it's good enough, clean it one more time, just because. Good luck -
P
LS rear main seal leaking
If it's a Gen III be aware that the cam position sensor is also mounted in the rear of block from the top. Sensor is fitted with an o'ring type seal that will not leak from top of block, but rear of block. Learned that while working for the general years ago. At the time the o'ring was not...- Poppy 87
- Post #13
- Forum: Tech Discussion
-
P
What have you done to your square lately??
Looks good. You may want to isolate that fuel line away from the coolant hose. Don't want to induce "heat" to the fuel prior to entering the carb -
P
Good dishwasher in garage
I worked with a guy back in the 1980's that used one to wash transmission cases. It was in a rental apartment though! -
P
Chuck’s engine build thread!
2 observations Chuck. Do you know what torque converter that is? That was not installed by the general. If you pulled out camel hump heads, check casting number/date codes. Numbers matching guys will pay $$ for them. Good luck. For what its worth, I always replace cam bearings.- Poppy 87
- Post #125
- Forum: Engine & Performance
-
P
Intermittent High Idle and Occasional Hesitation on Acceleration
My 87 had similar issue, found worn throttle shaft bushings in throttle body. Caused throttle plates contacting throttle body as well as vacuum leak. Inspect inside throttle bore while moving cable end of throttle shaft. There should be no contact between plates and housing, nor any lateral...- Poppy 87
- Post #10
- Forum: Tech Discussion
-
P
Vacuum lines for hvac system
PCV is typically post combustion gasses and is considered "dirty air" side. Preferred is "clean air side", direct intake manifold vacuum. LS intake has provision for brake booster, may need to tap into that, but be sure to plumb in a check valve so you don't loose brake assist.- Poppy 87
- Post #21
- Forum: Tech Discussion
-
P
Vacuum lines for hvac system
Pretty sure in the LS photo that is PCV, not manifold vacuum- Poppy 87
- Post #18
- Forum: Tech Discussion
-
P
New Old Guy with 76 C10 Shortbox
Welcome from coastal Georgia. Cool truck- Poppy 87
- Post #5
- Forum: Introduction
-
P
Hello from Georgia, 77' K10 4x4
Welcome from coastal GA. Nice truck- Poppy 87
- Post #3
- Forum: Introduction
-
P
Ford Trash Talk Thread lol
All that, but remember, it's still a Ferd...- Poppy 87
- Post #571
- Forum: Other Vehicles
-
P
snap on help
Not sure if you are aware, but Snap On has a website. I remember back in the day you could get those parts. I'd contact them.. -
P
357 build questions
No. The LT1 heads are Gen 2 small block and are unique to that engine.- Poppy 87
- Post #9
- Forum: Engine & Performance
-
P
communication protocol ecm/tcm for 2007 trucks
Pretty sure transfer case is high speed CAN and hvac is low speed CAN- Poppy 87
- Post #2
- Forum: Tech Discussion
-
P
New driveshaft in old truck?
Welcome to the site! I would try to find a local drive line shop. Sure you can have one built for less than $600. Good luck- Poppy 87
- Post #2
- Forum: Differential & Driveline
-
P
long block 350, looking for suppliers
Have you considered a GM crate engine? I think stock replacement is under 2K?- Poppy 87
- Post #6
- Forum: Engine & Performance
-
P
New guy here, from North Georgia
Welcome from coastal Georgia!!- Poppy 87
- Post #19
- Forum: Introduction
-
P
Fuel tank sending unit - 3 port or 4 port?
Adel clamps is what we call them in aviation- Poppy 87
- Post #9
- Forum: Tech Discussion
-
P
Squarebody Down! HELP - Member Roadside Assistance Volunteer Map
Coastal Georgia, 31302
