Search results

  1. Y

    Help with a hirn

    So alittle update here got the blinkers working sort of right hand side works,left hand sets the hazards off UNLESS i turn head lights on then it does nothing.....what in the actual **** if anyone has any ideas or has seen this before plz gimmie your 2¢... Tore column down again can find...
  2. Y

    Help with a hirn

    So ya messed around today fixing lights put a new alternator in, was feeling pretty good about the horn, then i discovered my blinkers don't work now first thought was that large connector with the bladed pins that had some loose ones on steering column and that's part of the problem because if...
  3. Y

    Help with a hirn

    Fixed it it's a bad spring in the steering column not the one for the horn button there's a second one underneath the steering wheel in the selector switch thought I was going to have to change the whole switch out which is a pain but was able to pry the back of it open and put a new spring inside
  4. Y

    Help with a hirn

    Ya I've narrowed it down to the steering column just got a wheel puller this is pretty lame all for a horn too much damn work luckily I got a parts truck sitting in my driveway
  5. Y

    Help with a hirn

    Ok thought i found it but no, there was some loose pins in a connector going up to the steering column fixed those actually have continuity through like blinker right turn signal or whatever up to an allen wrench that i drove in the horn button from the relay. However no matter what I do I...
  6. Y

    Help with a hirn

    Hey all I'm standing out here in the freezing cold trying to figure out what my horns not working it's an 87 square body TBI 350 I powered the horn relay on the orange wire continuity from the green wire out through the fuse box to the horn but no continuity from the horn relay pin to the horn...
  7. Y

    New impact: air vs battery powered?

    I have a 18v and a 36v, the 18v doesn't have enough power and the 36 will snap grade 8s in half....you can turn it down but i dont. Anyways 36v is the way to go for tough stuff otherwise i use pneumatic
  8. Y

    Compatible seat belts?

    Here
  9. Y

    Compatible seat belts?

    Anybody know of some 3-point seat belts that will for sure latch correctly with the factory latches? I replaced the driver's side and I had to cut the bolt out with my plasma cutter I'd rather spend $100 and get one that's compatible with the other side attached is a picture of the lap belt...
  10. Y

    spark plugs.... Over thinking!

    after reading this thread Ive realized I dont know **** about spark plugs some serious plug science in here
  11. Y

    Body part questions doors cab corners bed sides. Please help

    im restoring a k20 with aftermarket panels.....hes right they ****** suck i cant even figure out why one of my new bedsides pulls away at the top making tailgate difficult to close at least it doesnt fall down i guess
  12. Y

    Need an honest opinion

    my old truck silverado exactly like this I like the dark blue and gray but consider the silver it pops big time I'm restoring a K20 right now hopefully someday It will look like this its more of a off white then a silver but thats what i call it anyways
  13. Y

    Drop Height Fiasco

    god your truck has me drooling ive got a K20 im restoring was thinking about doing red and white, my old c10 was dark blue and silver very nice also but damn nice square body and sorry not useful at all i know
  14. Y

    BFGoodrich or Cooper?

    i dunno if anyone has said this but Good year duratrek 10plys At best ******* tires in the world for mud and snow absolutely amazing I've run them on the last two trucks I've had One of my trucks is a complete piece of **** people would still walk up to me and say tires looked awesome because...
  15. Y

    Correct front quadshocks for my 1987 V20 with plow

    hey all you guys got any recommendations for new quad shocks for my truck? it will occasionally have a heavy fisher plow on it in the winter months but im totally restoring this truck so it wont be worked too hard.what do you guys recommend for a good ride that can still handle a heavy load? (...
  16. Y

    AXLE SHAFT HELP!!!!!

    napa got me as well i have the exact same issue you do except im doing this its 5 fing degrees outside glad you got it done if ya dont mind though could you post the exact moog u joints you bought? i still have to pick up the right ones
  17. Y

    severely rusted stuck ujoint help

    thats why i started with a plasma cutter as well on top of all that its a pain to get the gas here and you need a license or contract to get your bottles filled at least in maine anyways and from how i understand it and im far from an expert i think the compressed air blasts the molten metal out...
  18. Y

    severely rusted stuck ujoint help

    its probly not good enough for a garage but ive had great luck with it and the price is pretty amazing i am using it exclusively on 220v though i have never tried it wired for 110v it can do both. it could cut that damn truck in half if i wanted it to
  19. Y

    severely rusted stuck ujoint help

    whatd you do take em back or grind em down?
  20. Y

    severely rusted stuck ujoint help

    o wow ty you this will be helpful
  21. Y

    severely rusted stuck ujoint help

    thanks for the help guys I'm dead in the water till Wednesday nobody has the inner bearings in stock that means I'll have one day to put this together before I have to go back to work in Sub-Zero temperatures fun fun I haven't even started the other side yet I got to ask this u joint thing is...
  22. Y

    severely rusted stuck ujoint help

    kinda late to the party with this one but ive got one last question for you guys....is there a bearing inside the spindle? i can see no sign of one left but looking at an lmc truck catalog i see a diagram showing parts im missing.... whoops sorry double post
  23. Y

    severely rusted stuck ujoint help

    kinda late to the party with this one but ive got one last question for you guys....is there a bearing inside the spindle? i can see no sign of one left but looking at an lmc truck catalog i see a diagram showing parts im missing....
  24. Y

    severely rusted stuck ujoint help

    you were dead on with this dude thats what i did and it worked great think ill do difficult joints like this from now on did have to be careful not to nic the yokes but omg it was so much easier then what i have been doing thank you p.s i have a cheap lotos plasma cutter bought on amazon for...
  25. Y

    severely rusted stuck ujoint help

    success! plasma cutter to the rescue even burned the caps through the center and either it was the heat or i weakend them enough but after that they popped right out. new u joint is installed and i realized after I installed it that Napa must have gave me the wrong one because the caps stick...

Latest posts

Forum statistics

Threads
48,413
Posts
1,066,820
Members
42,794
Latest member
Huffer8
Top